Control Techniques Unidrive HS30 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 66

background image

56

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

8

Diagnostics

Table 8-1 Trip indications

Ready to run

Run

The drive is now ready to run the motor. Close the Run
Forward or Run Reverse terminals.

Increasing and
decreasing speed

Changing the selected Analog frequency reference will
increase and decrease the speed of the motor.

Stopping

To stop the motor by following the selected deceleration rate,
open either the run forward or run reverse terminal. If the
enable terminal is opened while the motor is running, the drive
output is immediately disabled and the motor will coast to a
stop.

Users must not attempt to repair a drive if it is faulty, nor carry out fault diagnosis other
than through the use of the diagnostic features described in this chapter.
If a drive is faulty, it must be returned to the supplier of the drive for repair.

Trip

code

Condition

Description

C.Acc

NV Media Card Write fail

Unable to access the NV Media Card.

C.by

NV Media Card cannot be
accessed as it is being accessed
by an option module

An attempt has been made to access a file on NV Media Card,
but the NV Media Card is already being accessed by an option
module. No data is transferred.

C.cPr

NV Media Card file/data is different
to the one in the drive

A

C.cPr

trip is initiated if the parameters on the NV Media Card

are different to the drive.

C.d.E

NV Media Card data location
already contains data

Attempt has been made to store data on a NV Media Card in a
data block which already contains data.

C.dAt

NV Media Card data not found

Attempt has been made to access non-existent file or block on
the NV Media Card.

C.Err

NV Media Card data structure
error

Attempt has been made to access the NV Media Card but an
error has been detected in the data structure on the card.
Resetting the trip will cause the drive to erase and create the
correct folder structure.

C.FuL

NV Media Card full

There is not enough space left on the card.

C.OPt

NV Media Card trip; option
modules installed are different
between source drive and
destination drive

The parameter data or default difference data is being
transferred from the NV Media Card to the drive, but the option
module category is different between the source and destination
drives.

C.Pr

NV Media Card data blocks are not
compatible with the drive derivative

If Drive Derivative

is different between the source and target

drives. Refer to

Control User Guide

.

C.rdo

NV Media Card has the Read Only
bit set

Attempt has been made to modify a read-only NV Media Card or
a read-only data block.

C.rtg

NV Media Card Trip; The voltage
and / or current rating of the source
and destination drives are different

The current and / or voltage ratings are different between source
and destination drives.

C.SL

NV Media Card trip; Option module
file transfer has failed

The

C.SL

trip is initiated, if the transfer of an option module file

to or from a module failed because the option module does not
respond correctly.

C.tyP

NV Media Card parameter set not
compatible with current drive mode

The drive mode in the data block on the NV Media Card is
different from the current drive mode.

cL.A1

Analog input 1 current loss

Current loss was detected in current mode on Analog input 1
(Terminal 2).

Action

Detail

WARNING

«
...
54
55
56
57
58
...
»

Содержание Unidrive HS30



































































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS30

Бренд: wattio Страницы: 20

Бренд: Babybee Страницы: 28

Бренд: Hama Страницы: 8

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Бренд: Hiwin Страницы: 99

Бренд: Grundfos Страницы: 20

Бренд: schmersal Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды