Control Techniques Unidrive HS30 Скачать руководство пользователя страница 49

Страница: 49 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Defines the integral gain for frequency controller 1. See

Frequency Controller Proportional Gain Kp1

(Pr

Defines the time constant for the filter applied to the output of the frequency estimator system.

Spin Start Boost

(Pr

) is used by the algorithm that detects the frequency of a spinning motor when

the drive is enabled and

Catch A Spinning Motor

(Pr

)

≥

1. For smaller motors the default value of

1.0 is suitable, but for larger motors

Spin Start Boost

(Pr

) may need to be increased.

Spin Start Boost

(Pr

) is too small the drive will detect zero speed whatever the frequency of the

motor, and if

Spin Start Boost

(Pr

) is too large the motor may accelerate away from standstill when

the drive is enabled.

This parameter is the output of the PID controller. For further information, refer to the

Parameter

Reference Guide.

Proportional gain applied to the PID error. For further information, refer to the

Parameter Reference

Guide.

Frequency Controller Integral Gain Ki1

Num

RFC-A

0.00 to 655.35 s

/rad

0.10 s

/rad

Sensorless Mode Filter

Txt

RFC-A

4 (0), 5 (1), 6 (2), 8 (3), 12 (4),

20 (5) ms

4 (0) ms

Spin Start Boost

Num

0.0 to 10.0

1.0

RFC-A

PID1 Output

Num

±100.00 %

RFC-A

PID1 Proportional Gain

Num

0.000 to 4.000

1.000

RFC-A

Содержание Unidrive HS30



































































Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды

Control Techniques Unidrive HS30, Быстрый старт

Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды