Control Techniques Unidrive HS30 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 66

background image

24

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

5

Keypad and display

The keypad and display provide information to the user regarding the operating status of the drive,
alarms and trip codes, and provide the means for changing parameters, stopping and starting the
drive, and the ability to perform a drive reset.

Figure 5-1 Unidrive M300/HS30 keypad detail

(1) The Enter button is used to enter parameter view or edit mode, or to accept a parameter edit.
(2, 5) The Navigation keys can be used to select individual parameters or to edit parameter values. In
keypad mode, the ‘Up’ and ‘Down’ keys are also used to increase or decrease the motor speed.
(3) The Stop / Reset button (red) is used to stop and reset the drive in keypad mode. It can also be
used to reset the drive in terminal mode.
(4) The Start button (green) is used to start the drive in keypad mode.
(6) The Escape button is used to exit from the parameter edit / view mode or disregard a parameter
edit.

Table 5-1 Status indications

String

Description

Drive output stage

inh

The drive is inhibited and cannot be run. The Safe Torque
Off signals are not applied to Safe Torque Off terminals or
is set to 0.

Disabled

rdy

The drive is ready to run. The drive enable is active, but the
drive inverter is not active because the final drive run is not
active.

Disabled

StoP

The drive is stopped / holding zero speed.

Enabled

S.Loss

Supply loss condition has been detected.

Enabled

dc.inj

The drive is applying DC injection braking.

Enabled

Er

The drive has tripped and no longer controlling the motor.
The trip code appears in the display.

Disabled

UV

The drive is in the under voltage state either in low voltage
or high voltage mode.

Disabled

HEAt

The motor pre-heat function is active.

Enabled

7

1

2

3

6

5

4

«
...
22
23
24
25
26
...
»

Содержание Unidrive HS30



































































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS30

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: IBM Страницы: 105

Бренд: Idesco Страницы: 11

Бренд: B meters Страницы: 2

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 4

GAT ACCESS 6100

Бренд: Gantner Страницы: 4

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: xpr Страницы: 4

Бренд: SYR Страницы: 2

Бренд: K&K Страницы: 10

Бренд: Grundfos Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды