Control Techniques Unidrive HS30 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 66

background image

60

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

8.1 Alarm indications

In any mode, an alarm is an indication given on the display by alternating the alarm string with the
drive status string display. If an action is not taken to eliminate any alarm except "tuning”, “LS" or
“24.LoSt” the drive may eventually trip. Alarms are not displayed when a parameter is being edited.

Table 8-2 Alarm indications

U.S

User Save error / not completed

The

U.S

trip indicates that an error has been detected in the

user save parameters saved in non-volatile memory.

UP.uS

User Program trip

This trip can be initiated from within an onboard user program.
Refer to the

Control User Guide

.

UPrG

User Program

An error has been detected in the onboard user program image.
Refer to the

Control User Guide

.

Alarm string

Description

br.res

Brake resistor overload.

Braking Resistor Thermal Accumulator

in the drive has

reached 75.0 % of the value at which the drive will trip.Refer to the

Power

Installation Guide

OV.Ld

Motor Protection Accumulator

in the drive has reached 75.0 % of the value at

which the drive will trip and the load on the drive is >100 %, reduce motor current
(load). Refer to the

Parameter Reference Guide

d.OV.Ld

Drive over temperature.

Percentage Of Drive Thermal Trip Level

in the drive is

greater than 90 %. Refer to the

Parameter Reference Guide

tuning

The autotune procedure has been initialized and an autotune in progress.

LS

Limit switch active. Indicates that a limit switch is active and that is causing the
motor to be stopped.

Lo.AC

Low voltage mode. See

Low AC Alarm

in

Control User Guide.

I.AC.Lt

Current limit active. See

Current Limit Active

in

Control User Guide.

24.LoSt

24V backup not present. See

24V Alarm Loss Enable

in the

Control User Guide.

Trip

code

Condition

Description

«
...
58
59
60
61
62
...
»

Содержание Unidrive HS30



































































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS30

Бренд: XGAMING Страницы: 9

Бренд: DayTronic Страницы: 22

Бренд: DayTronic Страницы: 414

Бренд: Panamax Страницы: 16

Бренд: Parker Страницы: 4

Бренд: OJ Electronics Страницы: 8

Baby Born 828656

Бренд: Zapf Creation Страницы: 2

Бренд: Mazurczak Страницы: 9

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренд: Olsen Страницы: 4

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

CITY MICRO DOUBLE

Бренд: Baby Jogger Страницы: 9

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

Бренд: Texas Instruments Страницы: 25

Бренд: EBS Страницы: 118

IconRemote IR10A

Бренд: X10 Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды