Control Techniques Unidrive HS30 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 66

background image

Unidrive M300/HS30 Quick Start Guide

63

Issue Number: 7

11

UL listing information

11.1 UL file reference

All models are UL Listed to both Canadian and US requirements. The UL file reference is: NMMS/
7.E171230.

11.2 Option modules, kits and accessories

Option Modules, Control Pods, Installation Kits and other accessories for use with these drives are
UL Listed.

11.3 Enclosure ratings

All models are Open Type as supplied.

The drive enclosure is not classified as a fire enclosure. A separate fire enclosure must be provided.
A UL/ NEMA Type 12 enclosure is suitable.
When fitted with a conduit box the drives meet the requirements for UL Type 1. Type 1 enclosures
are intended for indoor use, primarily to provide a degree of protection against limited amounts of
falling dirt.
Remote Keypads are UL Type 12 when installed with the sealing washer and fixing kit provided.
When installed in a Type 1 or Type 12 enclosure, the drives may be operated in a compartment
handling conditioned air.

11.4 Mounting

Drives may be surface mounted using the appropriate brackets. Drives may be mounted singly or
side by side with suitable space between them (bookcase mounting).

11.5 Environment

Drives must be installed in a Pollution Degree 2 environment or better (dry, non-conductive pollution
only).
The drives have been evaluated for use at ambient temperatures up to 40 °C. The drives have
additionally been evaluated for 50

°

C and 55

°

C ambient air temperatures with a derated output.

11.6 Electrical Installation

OVERVOLTAGE CATEGORY

OVC III

SUPPLY

The drives are suitable for use on a circuit capable of delivering not more than 100,000 RMS
symmetrical amperes, 600 Volts AC Maximum.

TERMINAL TORQUE

Terminals must be tightened to the rated torque as specified in the Installation Instructions.

WIRING TERMINALS

Drives must be installed using cables rated for 75 °C operation, copper wire only.
Where possible, UL Listed closed-loop connectors sized according to the field wiring shall be used
for all field power wiring connections.

GROUND CONNECTION INSTRUCTIONS

UL Listed closed-loop connectors sized according to the field wiring shall be used for grounding
connections.

«
...
61
62
63
64
65
...
»

Содержание Unidrive HS30



































































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS30

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: UNITED Страницы: 22

Бренд: Hafele Страницы: 82

Бренд: Bartec Страницы: 26

Бренд: Baninni Страницы: 26

Бренд: V2 Страницы: 48

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: Gatekeeper Страницы: 28

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Waterway Страницы: 8

Бренд: D+H Страницы: 32

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды