background image

General 

1.1 SAFETY INSTRUCTIONS 

Before installing and using the Smoke Screen read, follow and retain this manual and safety instructions for future 
reference.   

To reduce the risk of severe injury or death to persons, or damage to the Smoke Screen: 

Do not work on the Smoke Screen unless qualified by the manufacturer to do so.

Disconnect the mains power supply before working in the heater block compartment or anywhere that mains
voltage is indicated by the warning labels shown below.

Install in accordance with the instructions in this manual.

Operate the Smoke Screen only from the type of power source indicated on the label.

Do not modify the Smoke Screen.

Adjust only the controls specified in this manual.

Use only consumables and replacement parts specified by the manufacturer.

Do not spill liquid of any type on, or inside, the Smoke Screen.

The following signs, or a variation, may be used for safety notices in this manual or on the Smoke Screen: 

This type of warning note is 
used to indicate possible 
electrical shock hazards that 
may cause serious injuries or 
death. 

This type of warning note is 
used to indicate the possibility 
of injury caused by hazards 
other than electrical shock. 

1.2 HOW DOES YOUR SMOKE SCREEN WORK? 

Your Smoke Screen passes a non-toxic fluid through an efficient heat exchanger to create smoke, or more accurately 
a thermally generated fog that obscures visibility, discouraging intruders from entering your premises.   

This fog is very persistent and will stay suspended in the room for a significant length of time until it is vented by 
opening the doors and windows.   

The Smoke Screen uses a sophisticated electronic control system to ensure it heats up to, and maintains, its ideal 
operating temperature using a minimal amount of electricity.   

The control system similarly provides a flexible interface with intruder detectors, alarm systems and remote 
monitoring centres to ensure that you are always protected and free of inadvertent activations.

 

WARNING

CAUTION

Содержание TITANIUM Ti100









































Отзывы: