Concept Smoke Screen TITANIUM Ti100 Скачать руководство пользователя | Manualshive

Страница: 30 / 40

background image

Batt Volt

Alarm = fault
Restore = OK

Condition of battery Voltage.

(Z1) Set Input

Alarm = active
Restore = OK

State of the selected input Zone.

Z2) Trigger

(Z3) Programmable

(Z4) Hold Off Inp

(Z5) Panic Trigger

(Z6) Isolate

DC Fuse

Alarm = fault
Restore = OK

State of the low voltage DC fuse on the PCB.

Pump Fuse

Alarm = fault
Restore = OK

State of the pump fuse on the PCB.

Batt Resistance

Alarm = fault
Restore = OK

Battery condition.

Block temp

Current block temperature.

Battery State

Charging
Discharging
Testing
Not connected

Status of the battery charging system.

Ready State

Local:R
Local:F
Global:R
Global:F

State of the selected output. When the system is
configured as Master and Slaves, Local = the state of the
Master Smokescreen and Global = the state of attached
slaves. For example, Ready "Local:R/Global:F" means that
the Master is ready but one or more of the slaves is not. If
either "Local" and/or "Global" is "F" then the system will
output a fail state.

Tamper Fault

Battery Fault

Mains Fault

Fluid Low Fault

Fluid Empty Fault

Smoke output

Output Closed
Output Opened

State of the selected output.

PGM1 output

PGM2 output

30

«
...
28
29
30
31
32
...
»

Содержание TITANIUM Ti100









































Отзывы:

Нет отзывов

Похожие инструкции для TITANIUM Ti100

Бренд: FED Страницы: 5

Бренд: JBL Страницы: 2

Бренд: JBL Страницы: 2

Бренд: C&K systems Страницы: 28

Бренд: C&K systems Страницы: 2

DUAL TEC DT-900 Series

Бренд: C&K systems Страницы: 2

Бренд: C&K systems Страницы: 40

Бренд: Veeder-Root Страницы: 3

Бренд: Fenton Страницы: 56

Бренд: Zadako Страницы: 15

Бренд: La Crosse Technology Страницы: 2

Бренд: Panasonic Страницы: 27

JBL CINEMA SB130

Бренд: Harman Страницы: 16

Бренд: Halma Страницы: 8

Бренд: FAAST Страницы: 12

Бренд: Response Alarms Страницы: 16

Бренд: Vizio Страницы: 20

Бренд: NAVAC Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды