Concept Smoke Screen TITANIUM Ti100 Скачать руководство пользователя

Страница: 26 / 40

(Z6) Isolate

Normally
closed

Not used
Normally Open
Normally closed
Double EOL
Single EOL
(EOL values available =
1k, 2k2, 2k7, 3K,
3K3,4K7, 5k6, 6k2)

Defines the type of input the Smoke
Screen requires to be isolated through
Zone 6.

Ready output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen is ready to activate.

Tamper output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen is not in tamper alarm.

Battery output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen battery power is ok.

Mains F.
output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen mains power is ok.

Fluid L. output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen fluid is above 50%.

Fluid E. output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen fluid is above empty.

Smoke output

Normal (NC)

Normal (NC)
Inverted (NO)

Defines the output state when the
Smokescreen is making smoke.

PGM 1/2/3
output*

Normal (NO)

Normal (NC)
Inverted (NO)

Sets the state of the PGM Outputs.
Settings available are “Normally
closed” and “Normally open”.

PGM 1/2/3
function*

Disabled

Function not in use.

Follow Pump Fuse F

PGM follows selected function.

Follow Nozzle F

Fire Panel Isolate

Follow Fluid Med

Follow Overheat

Follow Underheat

Follow Thermal Fault

Iris Mode

Not used

Follow Trouble/Tmp

PGM follows selected function.

Содержание TITANIUM Ti100









































Результаты поиска

Содержание TITANIUM Ti100

Отзывы:

Похожие инструкции для TITANIUM Ti100

Бренды по названию

Популярные бренды

Concept Smoke Screen TITANIUM Ti100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TITANIUM Ti100

Отзывы:

Похожие инструкции для TITANIUM Ti100

Бренды по названию

Популярные бренды