Concept Smoke Screen TITANIUM Ti100 Скачать руководство пользователя | Manualshive

Страница: 7 / 40

background image

Location

2

2.1 POSITIONING

The Smoke Screen should ideally be sited in a covert position away from prying eyes and thereby reducing the
possibility of tampering or an attack. The ideal place for the Smoke Screen is above a ceiling from where the smoke
plume is used to its best effect, bursting on the ground and spreading outwards and upwards through 360°. If no
suitable ceiling location is available then the next best location is a wall mounting close to ceiling.

Wall-mounting

The optimum wall mounting position for the Smoke Screen is 2.5 metres above the floor facing the area to be
protected and using an appropriate angle nozzle. The maximum recommended mounting-height above floor level is
3 metres, the minimum is 1 metre and there should be no obstacles within 1 metre of the smoke output nozzle. Also,
leave a minimum of 150mm clearance to the ceiling.

Ceiling-mounting

The optimum wall mounting position for the Smoke Screen is 2.5 metres above the floor facing the area to be
protected and using an appropriate angle nozzle. The maximum recommended mounting-height above floor level is
3 metres, the minimum is 1 metre and there should be no obstacles within 1 metre of the smoke output nozzle.

7

«
...
5
6
7
8
9
...
»

Содержание TITANIUM Ti100









































Отзывы:

Нет отзывов

Похожие инструкции для TITANIUM Ti100

Бренд: Vector Welding Страницы: 81

Бренд: U-Prox Страницы: 3

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 4

Бренд: Eastwood Страницы: 12

Бренд: Easy Clocking Страницы: 23

Бренд: TAD Страницы: 2

Бренд: Taco Страницы: 56

Бренд: Phase Technology Страницы: 11

Бренд: i3 International Страницы: 3

Бренд: Electro-Voice Страницы: 8

Бренд: R-Tech Страницы: 20

Бренд: Guardian Страницы: 2

Бренд: Q-See Страницы: 1

Бренд: Sennheiser Страницы: 2

Бренд: Karaoke USA Страницы: 16

Бренд: Okina USA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды