ComAp InteliDrive Mobile Скачать руководство пользователя

Страница: 164 / 261

ID-Mobile Global Guide

164

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

165

Description

The engine Requested RPM is decreased/increased when input is closed. Speed down has higher priority

when both Up and Down inputs are active. RPM inc/dec rate is defined by

BI Speed Ramp (page 85)

Engine speed can be set by analog input Requested RPM or by BI Speed Up and Down.

Following requested RPM initialization is valid when Analog input Requested RPM is not configured.

Requested RPM (Idle) = 0.

Requested RPM (Running) = 50% for SS (ECU 50%=Nominal RPM).

Requested RPM (Running) = 0% for AS.

Note:

Minimal Speed up and Speed down pulse duration is 110 ms to be accepted by controller.

Speed Up

back to List of LBI

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

Description

Forces controller NotReady state (=disables engine start).

StartBlocking

back to List of LBI

Содержание InteliDrive Mobile






































































































































































































































































Результаты поиска

Содержание InteliDrive Mobile

Отзывы:

Похожие инструкции для InteliDrive Mobile

Бренды по названию

Популярные бренды

ComAp InteliDrive Mobile, Глобальное руководство

Результаты поиска

Содержание InteliDrive Mobile

Отзывы:

Похожие инструкции для InteliDrive Mobile

Бренды по названию

Популярные бренды