ComAp InteliDrive Mobile Скачать руководство пользователя

Страница: 24 / 261

ID-Mobile Global Guide

BOOT

System booting

BI1 - BI8 polarity

Setting of polarity for activation of BIN1 to BIN8

BOUT

BOUT broken wire detection blocking for not used outputs

Note:

Analog outputs AOUT1–8 and analog inputs AIN 9-16 share connector pins 37 to 44 – see table below.

Each pin from this group can be used or for AIN or for AOUT (not both).

To use any analog input AIN9-16 the corresponding B Group jumper has to be disconnected and corresponding

AOUT can not be used.

Analog inputs AIN1-AIN8 can be used in any case - do not depend on AOUT1-AOUT8 configuration.

PIN

Function

AOUT1

AIN9

AOUT2

AIN10

AOUT3

AIN11

AOUT4

AIN12

AOUT5

AIN13

AOUT6

AIN14

AOUT7

AIN15

AOUT8

AIN16

2.8 Configuration examples

Function

A GROUP

B GROUP

C GROUP

AOUT: 0 - 24VBatt

3-2

2-1

OFF

AOUT: 0 - 10VDC

2-1

OFF

AOUT: 0 – 20 mA

2-1

3-2

OFF

AIN: 20 mA

OFF

AIN: 5 VDC

OFF

AIN: 24 VDC

OFF

AIN: 2.5 kOhm

OFF

AIN: PT1000

OFF

1+2

Note:

X … opened or closed

IMPORTANT: To use any analog output AOUT1-8 the corresponding C Group jumper has to be

disconnected. E.g. for AOUT1 has to be disconnected all C Group jumper AIN9. Connected jumper

has influence on AOUT.

Содержание InteliDrive Mobile






































































































































































































































































Результаты поиска

Содержание InteliDrive Mobile

Отзывы:

Похожие инструкции для InteliDrive Mobile

Бренды по названию

Популярные бренды

ComAp InteliDrive Mobile, Глобальное руководство

Результаты поиска

Содержание InteliDrive Mobile

Отзывы:

Похожие инструкции для InteliDrive Mobile

Бренды по названию

Популярные бренды