ComAp InteliDrive DCU Industrial Скачать руководство пользователя

Страница: 283 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

283

This module is compatible with MTU ECU-7 at communication speed 125 kbps when uploaded with firmware

1.2.0 and higher.

The detection of communication speed is indicated by fast flashing of status LED. Once the speed is detected

the module remains set for the speed even when the communication is lost. Renewal of communication speed

detection is done by reset of the module.

Available inputs/outputs

Analog inputs

8 channels

Can be configured as

Resistor three wire input

Current input

Voltage input

Impulse input

1 channel

Can be configured as

Impulse

Impulse/time

RPM

All inputs can be configured to any logical function or protection.

It is possible to connect up to 10 modules to the InteliGen-NT, InteliSys-NT or InteliMains-NT controllers or up

to 4 modules to the ID-DCU.

Inteli AIN8 module is connected to controller CAN1 bus.

Supported sensors

Sensors

User curves

PT100 [°C] (fix)

PT1000 [°C] (fix)

NI100 [°C] (fix)

NI1000 [°C] (fix)

PT100 [°F] (fix)

PT1000 [°F] (fix)

NI100 [°F] (fix)

NI1000 [°F] (fix)

0-250ohm (fix linear)

0-2400ohm (fix linear)

0-10k ohm (fix linear)

+-1V (fix linear)

Содержание InteliDrive DCU Industrial































































































































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды

ComAp InteliDrive DCU Industrial, Глобальное руководство

Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды