ComAp InteliDrive DCU Industrial Скачать руководство пользователя

Страница: 27 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

3 Application overview

3.1 ID-DCU Industrial

back to Table of contents

3.1 ID-DCU Industrial

3.1.1 Default archives

The ID-DCU Industrial controller can be configured for auxiliary, emergency, combined (constant speed

engines) or propulsion mode engines. The configuration can be changed in the DriveConfig software by

selecting appropriate archive file.

Application

Archive file

Available modes

Engine start / stop

Single

Speed

ID-DCU

Industrial-SS-

3.4.0.aid

OFF - RUN

Blackout Start

Remote Start

Remote Stop

Rem Start/Stop

ID-DCU IndustrialStart / Stop

button

All Speed

ID-DCU

Industrial-AS-

3.4.0.aid

OFF - RUN

Blackout Start

Remote Start

Remote Stop

Rem Start/Stop

ID-DCU IndustrialStart / Stop

button

3.1.2 Operational modes

LOC (Local) mode

LOC

(Local) mode can be set in any mode mentioned above –

AUX, EME, HRB, PRP

. ID-DCU Industrial

receives only commands entered from the ID-DCU Industrial front panel in LOC (Local) mode. All external

interfaces – binary inputs

Remote Start, Blackout Start, RemRepStart, Remote Stop, Rem Start/Stop

and

serial line commands are disabled.

LOC

(Local) mode is activated and deactivated using ID-DCU Industrial front panel buttons: Enter + Mode→ to

activate, Enter + ←Mode to deactivate. Active

LOC

(Local) mode is indicated in the upper right corner of the ID-

DCU Industrial display.

OFF mode

All ID-DCU Industrial controller is switched off. Engine can’t be started or running engine is stopped,

prelubrication function is not active. Firmware and controller configuration can be changed in

OFF

mode only.

Содержание InteliDrive DCU Industrial































































































































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды

ComAp InteliDrive DCU Industrial, Глобальное руководство

Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды