Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 79 / 113

Specifications

7802P

Internal LED Ring Light White, Red, Blue or IR LED ring light used with the illumination accessory (ISLM-7000-xxx).

White LED color temperature: 4000 K

Red LED wavelength: 617 nm

Blue LED wavelength: 455 nm

IR LED wavelength: 850 nm

Note

For color vision systems, the white LED ring light should be used.

Refer to DataMan documentation for DataMan accessory specifications.

In-Sight Illumination
Accessory
(ISLM-7000-xxx)

Cover is compliant with ANSI Z87.1-2003 Drop-Ball Impact Test (no fracture, 25.4mm
diameter steel ball, vertical drop from 127cm).

In-Sight Autofocus
Module Accessory
(ISAF-7000-8mm)

Number of Focus Cycles: 20,000

Network
Communication

1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3 TCP/IP Protocol. Supports
DHCP, static and link-local IP address configuration.

1588 Support

Timestamp Resolution: 8ns
Synchronization Accuracy Through Transparent Clock: 5μs

Serial Communication

RS-232C when connected to the Breakout cable

or a compatible I/O module.

Power Consumption

24VDC ±10%, 1.5A maximum.

Power Output

24VDC @ 750mA maximum to external light.

Material

Die-cast and extruded aluminum housing.

Finish

Painted.

Mounting

Four M3 threaded mounting holes. 1/4-20, M6 and flathead mounting holes also available on
mounting bracket accessory (ISB-7000-7K). M4 mounting holes also available on mounting
bracket accessory (ISB-7000-5K).

Dimensions

49.4mm (1.94in) x 60.5mm (2.38in) x 90.1mm (3.55in).

95.3mm (3.21in) x 60.5mm (2.38in) x 90.1mm (3.55in) with C-Mount cover accessory

(COV-7000-CMNT).

116.3mm (4.58in) x 60.5mm (2.38in) x 90.1mm (3.55in) with C-Mount cover accessory

(COV-7000-CMNT-EX).

131.7 (5.19in) x 68.0 (2.68in) x 90.1mm (3.55in) with C-Mount cover accessory (COV-

7000-CMNT-LG).

161.7 (6.37in) x 68.0 (2.68in) x 90.1mm (3.55in) with C-Mount cover accessory (COV-

7000-CMNT-LG) and C-Mount cover extender accessory (COV-7000-CMNT-LGX).

91.1mm (3.59in) x 88.9mm (3.50in) x 97.2mm (3.83in) with illumination accessory

(ISLM-7000-xxx).

If hardware handshaking is required, an I/O module must be used.

Specifications

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды