Cognex In-Sight 7600 Скачать руководство пользователя | Manualshive

Страница: 84 / 113

background image

7902P/7905 Vision System Specifications

Specifications

7902P

7905

7905C

Minimum Firmware
Requirement

In-Sight version 5.7.4

In-Sight version 5.6.0

Job/Program Memory

7.2GB non-volatile flash memory; unlimited storage via remote network device.

Image Processing Memory

512MB SDRAM

SD Card

1 Micro SD card slot with an 8GB SD card pre-installed for saving job and image files. The
vision system supports SD cards with a maximum capacity of 32GB, formatted with a
FAT32 file system.

Sensor Type

2/3-inch CMOS, global shutter

Sensor Properties

7.8mm diagonal, 3.45 x
3.45µm sq. pixels

11.1mm diagonal, 3.45 x 3.45µm sq. pixels

Maximum Image
Resolution (pixels)

1

1920 x 1200

2448 x 2048

Electronic Shutter Speed

21µs to 1000ms

Acquisition

Rapid reset, progressive scan, full-frame integration. High
Dynamic Range (HDR) available.

Rapid reset, progressive
scan, full-frame integration.

Bit Depth

256 grey levels (8 bits/pixel)

24-bit color

Frames Per Second (FPS)

2

55 FPS

32 FPS

17 FPS

Lens Type

C-Mount

Trigger

1 opto-isolated, acquisition trigger input.

Discrete Inputs

l

3 general-purpose inputs when connected to the Breakout cable.

3

l

8 general-purpose inputs available when connected to the CIO-MICRO I/O Module

via the I/O Module cable.

l

7 general-purpose inputs available when connected to the CIO-1400 I/O

Expansion Module via the I/O Module cable.

Discrete Outputs

l

4 high-speed outputs when connected to the Breakout cable.

4

l

2 high-speed outputs, plus 8 general-purpose outputs available when connected

to the CIO-MICRO I/O Module via the I/O Module cable.

l

2 high-speed outputs, plus 6 general-purpose outputs available when connected

to the CIO-1400 I/O Expansion Module via the I/O Module cable.

Status LEDs

SD Card Status, Pass/Fail LED and Indicator Ring, Network LED and Error LED.

1

You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it
increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the

In-Sight

®

Explorer Help

file for more

information.

2

Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated
acquisition trigger, and assumes there is no user interface connection to the vision system.

3

When connected to the Breakout cable, the vision system allows for bi-directional, general-purpose inputs and high-speed outputs for IN 2 /
HSOUT 2 and IN 3 / HSOUT 3. These lines are configured as outputs by default.

4

When connected to the Breakout cable, the vision system allows for bi-directional, general-purpose inputs and high-speed outputs for IN 2 /
HSOUT 2 and IN 3 / HSOUT 3. These lines are configured as outputs by default.

84

Specifications

«
...
82
83
84
85
86
...
»

Содержание In-Sight 7600


















































































































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 7600

Бренд: DEWESOFT Страницы: 59

Бренд: Emerson Страницы: 35

Бренд: Hitachi Страницы: 45

Бренд: Hitachi Страницы: 73

Бренд: Hitachi Страницы: 86

MPEGCAM MP-EG1A

Бренд: Hitachi Страницы: 101

Бренд: Hitachi Страницы: 85

Бренд: Hitachi Страницы: 170

Бренд: Hitachi Страницы: 212

Бренд: Hitachi Страницы: 12

Бренд: JVC Страницы: 144

Бренд: JVC Страницы: 56

Бренд: JVC Страницы: 35

Бренд: JVC Страницы: 16

Бренд: JVC Страницы: 128

Бренд: JVC Страницы: 72

Бренд: JVC Страницы: 64

Бренд: JVC Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды