Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 48 / 113

Connect the External Light Cable (Optional)

The vision system's LIGHT connector is used to connect the External Light cable to an external lighting device, providing

power and strobe control. The External Light cable can be connected to either a continuous or strobed lighting device.

For a list of supported accessories, refer to

External Lights

on page 20

Note

: The vision system supports connecting an integrated illumination accessory to the vision system's faceplate

and connecting an external light to the vision system's LIGHT connector, but does not support using both lighting
devices simultaneously.

1. Remove the protective cap from the LIGHT connector, if present.

2. Connect the External Light cable’s M12 connector to the vision system's LIGHT connector.

3. Connect the other end of the Light cable to an external lighting device (for example, a strobe light). For more

information, refer to

External Light Connector

on page 91

Connect the Ethernet Cable

CAUTION

The Ethernet cable shield must be grounded at the far end. Whatever this cable is plugged into

(typically a switch or router) should have a grounded Ethernet connector. A digital voltmeter should be used to
validate the grounding. If the far end device is not grounded, a ground wire should be added in compliance with
local electrical codes.

1. Connect the Ethernet cable's M12 connector to the vision system ENET connector.

2. Connect the Ethernet cable’s RJ-45 connector to a switch/router or PC, as applicable.

Installation

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды