Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 6 / 113

Precautions

To reduce the risk of injury or equipment damage when you install the Cognex product, observe the following

precautions:

The vision system requires a UL or NRTL listed power supply with a 24VDC output that meets the following rating

requirements:

At least 2A continuous current.

A maximum short circuit current of less than 8A.

A maximum power of less than 100VA and marked as a Limited Power Source (LPS) or National

Electrical Code (NEC) Class 2.

Any other voltage creates a risk of fire or shock and can damage the components. Applicable national and local

wiring standards and rules must be followed.

This product is intended for industrial use in automated manufacturing or similar applications.

The safety of any system incorporating this product is the responsibility of the assembler of the system.

Do not install Cognex products where they are exposed to environmental hazards such as excessive heat, dust,

moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static electricity.

Route cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of

damage or malfunction from the following causes: over-voltage, line noise, electrostatic discharge (ESD), power

surges, or other irregularities in the power supply.

Do not expose the image sensor to laser light. Image sensors can be damaged by direct, or reflected, laser light.

If your application requires laser light that might strike the image sensor, use a lens filter at the corresponding

laser wavelength. For suggestions, contact your local integrator or application engineer.

This product does not contain user-serviceable parts. Do not make electrical or mechanical modifications to

product components. Unauthorized modifications can void your warranty.

Changes or modifications not expressly approved by the party responsible for regulatory compliance could void

the user’s authority to operate the equipment.

Include service loops with cable connections.

Ensure that the cable bend radius begins at least six inches from the connector. Cable shielding can be

degraded or cables can be damaged or wear out faster if a service loop or bend radius is tighter than 10X the

cable diameter.

This device should be used in accordance with the instructions in this manual.

All specifications are for reference purposes only and can change without notice.

Precautions

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды