Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 18 / 113

DataMan Lenses, Lights and Covers

The following DataMan accessories are also supported with the In-Sight vision system for S-Mount/M12 manual focus

lens configurations. DataMan lenses are only supported with DataMan lights and covers.

Note

The following S-Mount/M12 lenses are supported. If a different lens is used, the following restrictions apply:

At infinity focus, the back focal length must be greater than 5.5 mm.

Close up, the back focal length of the lens cannot be greater than 10 mm.

For the In-Sight 7905, the vision system image circle is larger than the S-Mount/M12 lenses used in the

autofocus module (ISAF-7000-8mm) and the S-Mount/M12 adapter kit (ISLN-7000-SMNT), resulting in

mechanical vignetting in the image when using any S-Mount/M12 lens. Therefore, S-Mount/M12 lenses are

not recommended. For more information, see

Mechanical Vignetting

on page 110

Accessory

Part Number

Accessory

Image

10.3mm M12 lens with locking (DM300-LENS-10) and 10.3 mm IR M12
lens with locking

DM300-LENS-10-IR

16mm M12 lens with locking

DM300-LENS-16

25mm M12 lens with lens spacer and hex wrench (also requires
Extension kit)

DM300-LENS-25

Extension kit

DM300-EXT

Clear cover

DM300-CLCOV

Clear cover with white LED illumination

DM300-CLCOV-WHI

Diffuse cover with red LED illumination

DM300-DLCOV-RE

Diffuse cover with blue LED illumination

DM300-DLCOV-BL

Diffuse cover with IR LED illumination

DM300-DLCOV-IR

Polarized cover with red LED illumination

DM300-PLCOV-RE

Introduction

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды