Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 17 / 113

S-Mount/M12 Manual Focus Accessories

Note

The following S-Mount/M12 lenses are supported. If a different lens is used, the following restrictions apply:

At infinity focus, the back focal length must be greater than 5.5mm.

Close up, the back focal length of the lens cannot be greater than 13mm.

The DataMan clear cover accessory (DM300-CLCOV) is supported with In-Sight S-Mount/M12 manual focus

lenses and provides an IP65 rating.

For the In-Sight 7905, the vision system image circle is larger than the S-Mount/M12 lenses used in the

autofocus module (ISAF-7000-8mm) and the S-Mount/M12 adapter kit (ISLN-7000-SMNT), resulting in

mechanical vignetting in the image when using any S-Mount/M12 lens. Therefore, S-Mount/M12 lenses are

not recommended. For more information, see

Mechanical Vignetting

on page 110

Accessory

Part Number

Accessory Image

6mm M12 lens

LM12-06-01

8mm M12 lens

LM12-08-01-F2.2

12mm M12 lens

LM12-12-01-F2.3

16mm M12 lens

LM12-16-01

25mm M12 lens

LM12-25-01

S-Mount/M12 adapter kit:

S-Mount/M12 adapter

13mm lens locking cone (P/N 1000000178)

14mm lens locking cone (P/N 372-1270R)

Installation tool

Note

: The S-Mount/M12 adapter kit (ISLN-7000-SMNT) is

required when installing In-Sight S-Mount/M12 manual focus
lenses.

ISLN-7000-SMNT

Clear cover

DM300-CLCOV

Introduction

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды