Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 73 / 113

Specifications

7600

7600C

Status LEDs

SD Card Status, Pass/Fail LED and Indicator Ring, Network LED and Error LED.

Internal LED Ring Light White, Red, Blue or IR LED ring light used with the illumination accessory (ISLM-7000-xxx).

White LED color temperature: 4000 K

Red LED wavelength: 617 nm

Blue LED wavelength: 455 nm

IR LED wavelength: 850 nm

Note

For color vision systems, the white LED ring light should be used.

Refer to DataMan documentation for DataMan accessory specifications.

In-Sight Illumination
Accessory
(ISLM-7000-xxx)

Cover is compliant with ANSI Z87.1-2003 Drop-Ball Impact Test (no fracture, 25.4mm
diameter steel ball, vertical drop from 127cm).

In-Sight Autofocus
Module Accessory
(ISAF-7000-8mm)

Number of Focus Cycles: 20,000

Network
Communication

1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3 TCP/IP Protocol. Supports
DHCP, static and link-local IP address configuration.

1588 Support

Timestamp Resolution: 8ns
Synchronization Accuracy Through Transparent Clock: 5μs

Serial Communication

RS-232C when connected to the Breakout cable

or a compatible I/O module.

Power Consumption

24VDC ±10%, 1.5A maximum.

Power Output

24VDC @ 750mA maximum to external light.

Material

Die-cast and extruded aluminum housing.

Finish

Painted.

Mounting

Four M3 threaded mounting holes. 1/4-20, M6 and flathead mounting holes also available on
mounting bracket accessory (ISB-7000-7K). M4 mounting holes also available on mounting
bracket accessory (ISB-7000-5K).

Dimensions

35.7mm (1.41in) x 60.5mm (2.38in) x 90.1mm (3.55in).

81.7mm (3.21in) x 60.5mm (2.38in) x 90.1mm (3.55in) with C-Mount cover accessory

(COV-7000-CMNT).

102.7mm (4.04in) x 60.5mm (2.38in) x 90.1mm (3.55in) with C-Mount cover accessory

(COV-7000-CMNT-EX).

77.5mm (3.05in) x 88.9mm (3.50in) x 97.2mm (3.83in) with Illumination accessory

(ISLM-7000-xxx).

Weight

Vision system with no accessories attached: 240 g (8.47 oz.)

Standard plastic C-Mount cover (COV-7000-CMNT): 35 g (1.23 oz.)

Standard extended plastic C-Mount cover (COV-7000-CMNT-EX): 43 g (1.52 oz.)

Autofocus module (ISAF-7000-8mm): 121.5 g (4.29 oz.)

Illumination (ISLM-7000-WHI): 153.5 g (5.41 oz.)

If hardware handshaking is required, an I/O module must be used.

Specifications

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды