Cognex In-Sight 7600 Скачать руководство пользователя | Manualshive

Страница: 52 / 113

background image

2. Connect a frame ground wire to the I/O module’s Frame Ground terminal. Connect the other end of the frame

ground wire to frame ground.

CAUTION

:

The shield ground connections of the RS-232 port, LAN port, PoE port, I/O port and Frame

Ground terminal are internally connected. The system grounding is at a zero ground potential. This zero-
ground potential extends through the cable and to peripheral equipment, such as a vision system or PLC.
To ensure safe operating conditions, check ground connections to ensure that they meet a zero ground
potential.

3. Connect the I/O module's I/O wires.

a. Determine how I/O devices will be connected to the I/O module’s input and output terminals.

b. To loosen the appropriate screw terminals, use a screwdriver.

c. Connect the input and output wires to the input and output terminals.

d. Connect the other end of the input and output wires to the corresponding I/O device.

e. Tighten the screw terminals with the screwdriver to secure the wire leads in the terminal block; the

maximum torque is 0.1921 Nm (1.7 in-lb).

4. To connect the vision system to a serial device, plug a RS-232 serial cable (DB9 male connector) into the I/O

module’s RS-232 port and connect the other end of the cable to the serial device. Tighten the connector screws

to secure it to the I/O module.

5. Connect to an Ethernet network.

a. Connect a LAN cable (RJ-45 connector) to the I/O module’s LAN port.

b. Connect the other end of the LAN cable to a switch/router or PC, as applicable.

6. Connect the vision system's Ethernet cable.

a. Connect the Ethernet cable's M12 connector to the vision system ENET connector.

b. Connect the Ethernet cable’s RJ-45 connector to the I/O module’s PoE port or to a switch/router, as

applicable.

7. (Optional) Connect the I/O Module cable (CCB-PWRIO-MOD-xx) to the vision system to gain access to the I/O

module's , TRIGGER-, HS OUT 0, HS OUT 1 and HS COMMON terminals.

a. Connect the I/O Module cable’s M12 connector to the vision system’s PWR connector.

b. Connect the I/O Module cable’s DB15 connector to the I/O module’s I/O connector.

c. Restore power to the 24VDC power supply and turn it on if necessary.

52

Installation

«
...
50
51
52
53
54
...
»

Содержание In-Sight 7600


















































































































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 7600

Бренд: GE Страницы: 58

Бренд: GE Страницы: 58

Бренд: GE Страницы: 2

Бренд: Samsung Страницы: 7

Бренд: Samsung Страницы: 2

Бренд: Lavod Страницы: 21

Бренд: Samsung Страницы: 117

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 16

Handycam CCD-F45

Бренд: Sony Страницы: 18

Бренд: Sony Страницы: 20

Handycam CCD-F45

Бренд: Sony Страницы: 28

Handycam CCD-F50

Бренд: Sony Страницы: 32

XDCAM EX PMW-F3

Бренд: Sony Страницы: 26

Бренд: Sony Страницы: 41

Handycam CCD-F73

Бренд: Sony Страницы: 56

Handycam CCD-FX200

Бренд: Sony Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды