Cognex In-Sight 7600 Скачать руководство пользователя | Manualshive

Страница: 54 / 113

background image

2. Connect a frame ground wire to the I/O module’s Frame Ground terminal. Connect the other end of the frame

ground wire to frame ground.

CAUTION

:

The shield ground connections of the RS232 OUT port, SENSOR port and Frame Ground

terminal are internally connected. The system grounding is designed to be at a zero ground potential; this
zero ground potential extends through the cable and to peripheral equipment (e.g. a vision system, PLC,
etc.). To ensure safe operating conditions, it is strongly recommended that all ground connections are
checked to ensure that a zero ground potential is met.

3. Connect the I/O module's I/O wires.

a. Determine how I/O devices will be connected to the I/O module’s input and output terminals.

b. To loosen the appropriate screw terminals, use a screwdriver.

c. Connect the input and output wires to the input and output terminals.

d. Connect the other end of the input and output wires to the corresponding I/O device.

e. Tighten the screw terminals with the screwdriver to secure the wire leads in the terminal block; the

maximum torque is 0.4 Nm (3.5 in-lb).

4. To connect the vision system to a serial device, plug an RS-232 serial cable (DB9 male connector) into the I/O

module’s RS232 OUT port and connect the other end of the cable to the serial device. Tighten the connector

screws to secure it to the I/O module.

5. Connect the I/O Module cable (CCB-PWRIO-MOD-xx) to the vision system.

a. Connect the I/O Module cable’s M12 connector to the vision system’s PWR connector.

b. Connect the I/O Module cable’s DB15 connector to the I/O module’s SENSOR port.

c. Restore power to the 24VDC power supply and turn it on if necessary.

54

Installation

«
...
52
53
54
55
56
...
»

Содержание In-Sight 7600


















































































































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 7600

Palmcorder VM-575

Бренд: Quasar Страницы: 40

Бренд: Pentax Страницы: 40

Бренд: Twenty20 Corporation Страницы: 14

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 52

EVI-D100 (NTSC)

Бренд: Sony Страницы: 128

Бренд: Smarty Страницы: 31

Бренд: Stahl Страницы: 214

Бренд: WWAlarm Страницы: 8

Бренд: Babies R' Us Страницы: 2

Бренд: Matsushita Electric Страницы: 156

HAC-HFW2401R-Z-IRE6

Бренд: Dahua Страницы: 15

Pocket Cam M18205

Бренд: Panta Страницы: 56

Бренд: Abus Страницы: 52

Бренд: Canon Страницы: 25

Бренд: Canon Страницы: 23

Бренд: Samsung Страницы: 66

Бренд: Canon Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды