Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 11 / 113

Accessories

You can purchase the following components separately. For a list of options and accessories, contact your local Cognex

sales representative.

In-Sight Lenses, Lights and Covers

The following In-Sight lenses, lights and covers are supported with the vision system.

C-Mount Standard and Extended Covers

Note

When using a C-Mount lens, the following restrictions apply:

Maximum thread length is 5.25mm.

The C-Mount lens threads and body cannot protrude more than 6.5mm in length into the vision

system when screwed in unless the diameter of the back lens is smaller than 14.75mm. If the C-

Mount lens threads and body protrude more than 6.5mm, you can add a spacer between the lens

and vision system. However, the spacer decreases the working distance.

Refer to

C-Mount Lens Clearance Dimensions

on page 108

for more information.

CAUTION

If installing a C-Mount cover, the illumination accessory (ISLM-7000-xxx) PCB should not be installed to

the vision system. Refer to

Remove the Illumination Accessory PCB

on page 111

for steps to safely remove the

PCB and avoid damage to the vision system.

Accessory

Part Number

Accessory Image

Standard plastic C-Mount cover and lens cover adapter.

Note

: If using the COV-7000-CMNT cover, the maximum lens

length is 41mm, the maximum lens body diameter is 36.5mm
and the maximum diameter including locking screws is 47mm.

COV-7000-CMNT

Standard extended plastic C-Mount cover and lens cover adapter.

Note

: If using the COV-7000-CMNT-EX cover, the maximum

lens length is 62mm, the maximum lens body diameter is
36.5mm and the maximum diameter including locking screws
is 46.5mm.

COV-7000-CMNT-EX

Wide plastic C-Mount cover and lens cover adapter. This accessory
is only supported with the In-Sight 7802P, 7902P and 7905 vision
system.

Note

: If using the COV-7000-CMNT-LG cover, the maximum

lens length is 77mm, the maximum lens body diameter is
55mm and the maximum diameter including locking screws is
55mm.

COV-7000-CMNT-LG

Wide plastic 30mm C-Mount extender, compatible with the
COV-7000-CMNT-LG cover. This accessory is only supported with
the In-Sight 7802P, 7902P and 7905 vision system.

COV-7000-CMNT-LGX

Introduction

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды