Cognex In-Sight 7600 Скачать руководство пользователя | Manualshive

Страница: 78 / 113

background image

7802P Vision System Specifications

Specifications

7802P

Minimum Firmware
Requirement

In-Sight version 5.7.4

Job/Program Memory

7.2GB non-volatile flash memory; unlimited storage via remote network device.

Image Processing
Memory

512MB SDRAM

SD Card

1 Micro SD card slot with an 8GB SD card pre-installed for saving job and image files. The
vision system supports SD cards with a maximum capacity of 32GB, formatted with a FAT32
file system.

Sensor Type

2/3-inch CMOS, global shutter

Sensor Properties

7.8mm diagonal, 3.45 x 3.45µm sq. pixels

Maximum Image
Resolution (pixels)

1

1920 x 1200

Electronic Shutter
Speed

21µs to 1000ms

Acquisition

Rapid reset, progressive scan, full-frame integration. High Dynamic Range (HDR) available.

Bit Depth

256 grey levels (8 bits/pixel)

Frames Per Second
(FPS)

2

55 FPS

Lens Type

C-Mount or S-Mount/M12

Trigger

1 opto-isolated, acquisition trigger input.

Discrete Inputs

l

3 general-purpose inputs when connected to the Breakout cable.

3

l

8 general-purpose inputs available when connected to the CIO-MICRO I/O Module via

the I/O Module cable.

l

7 general-purpose inputs available when connected to the CIO-1400 I/O Expansion

Module via the I/O Module cable.

Discrete Outputs

l

4 high-speed outputs when connected to the Breakout cable.

4

l

2 high-speed outputs, plus 8 general-purpose outputs available when connected to

the CIO-MICRO I/O Module via the I/O Module cable.

l

2 high-speed outputs, plus 6 general-purpose outputs available when connected to

the CIO-1400 I/O Expansion Module via the I/O Module cable.

Status LEDs

SD Card Status, Pass/Fail LED and Indicator Ring, Network LED and Error LED.

1

You can configure the number of image sensor rows and set them in the In-Sight Explorer software. If you decrease the number of rows, it
increases the frames per second acquired by the vision system. Refer to the AcquireImage topic in the

In-Sight

®

Explorer Help

file for more

information.

2

Maximum frames per second are job-dependent, based on the minimum exposure for a full image frame capture using the dedicated
acquisition trigger, and assumes there is no user interface connection to the vision system.

3

When connected to the Breakout cable, the vision system allows for bi-directional, general-purpose inputs and high-speed outputs for IN 2 /
HSOUT 2 and IN 3 / HSOUT 3. These lines are configured as outputs by default.

4

When connected to the Breakout cable, the vision system allows for bi-directional, general-purpose inputs and high-speed outputs for IN 2 /
HSOUT 2 and IN 3 / HSOUT 3. These lines are configured as outputs by default.

78

Specifications

«
...
76
77
78
79
80
...
»

Содержание In-Sight 7600


















































































































Отзывы:

Нет отзывов

Похожие инструкции для In-Sight 7600

Palmcorder VM-575

Бренд: Quasar Страницы: 40

Бренд: Sony Страницы: 2

Digital HDVS HDCAM HDW-730S

Бренд: Sony Страницы: 19

Digital HDVS HDCAM HDW-730S

Бренд: Sony Страницы: 22

Бренд: Sony Страницы: 38

Digital Video Camera Recorder

Бренд: Sony Страницы: 48

Digital betacam DVW-707P

Бренд: Sony Страницы: 32

Digital Handycam DCR-PC8E

Бренд: Sony Страницы: 41

Digital Handycam DCR-TRV130E

Бренд: Sony Страницы: 53

Digital Handycam DCR-TRV203

Бренд: Sony Страницы: 84

DSC-F55 - Cyber-shot Digital Still Camera

Бренд: Sony Страницы: 108

Бренд: Sony Страницы: 128

DIGITAL HANDYCAM DCR-TR7000E

Бренд: Sony Страницы: 120

Digital Handycam DCR-TRV510

Бренд: Sony Страницы: 136

Digital Handycam DCR-TRV10

Бренд: Sony Страницы: 163

Digital betacam DVW-970

Бренд: Sony Страницы: 162

Digital Handycam DCR-TRV10

Бренд: Sony Страницы: 182

Digital Handycam DCR-PC8E

Бренд: Sony Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды