Cognex In-Sight 7600 Скачать руководство пользователя

Страница: 25 / 113

Installation

Read this section to learn how the vision system connects to its standard components and accessories. For a list of

options and accessories, contact your Cognex sales representative.

Note

: Cables are sold separately.

CAUTION

All cable connectors are keyed to fit the connectors on the vision system. Do not force the connections

or damage may occur.

Install the Lens, Lighting and Cover

You can choose between a variety of different C-Mount and S-Mount/M12 lenses and covers to install to the vision

system. Refer to

In-Sight Lenses, Lights and Covers

on page 11

and

DataMan Lenses, Lights and Covers

on page 18

for

a complete list of options and accessories.

Install the C-Mount Lens and Cover (COV-7000-CMNT or
COV-7000-CMNT-EX)

Complete the following steps to install a C-Mount lens and cover to the vision system. The C-Mount covers are optional

accessories and required for IP67 protection.

Note

When using a C-Mount lens, the following restrictions apply:

Maximum thread length is 5.25mm.

The C-Mount lens threads and body cannot protrude more than 6.5mm in length into the vision

system when screwed in unless the diameter of the back lens is smaller than 14.75mm. If the C-

Mount lens threads and body protrude more than 6.5mm, you can add a spacer between the lens

and vision system. However, the spacer decreases the working distance.

If using the COV-7000-CMNT cover, the maximum lens length is 41mm, the maximum lens body diameter is

36.5mm and the maximum diameter including locking screws is 47mm.

If using the COV-7000-CMNT-EX cover, the maximum lens length is 62mm, the maximum lens body

diameter is 36.5mm and the maximum diameter including locking screws is 46.5mm.

CAUTION

If installing a C-Mount cover, the illumination accessory (ISLM-7000-xxx) PCB should not be installed to

the vision system. Refer to

Remove the Illumination Accessory PCB

on page 111

for steps to safely remove the

PCB and avoid damage to the vision system.

1. Remove the rubber faceplate covering the image sensor window, if present.

2. Remove the protective film covering the threaded lens opening, if present.

3. Place the adapter on the faceplate of the vision system. Insert the four adapter screws and tighten; the maximum

torque is 0.90 Nm (8 in-lb).

4. Thread the lens into the vision system.

Installation

Содержание In-Sight 7600


















































































































Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды

Cognex In-Sight 7600, Справочное руководство

Результаты поиска

Содержание In-Sight 7600

Отзывы:

Похожие инструкции для In-Sight 7600

Бренды по названию

Популярные бренды