manualshive.com logo in svg

COBHAM GR716, Расширенный технический описатель и руководство пользователя, Страница: 431 / 547

Поделиться
Скачать
COBHAM GR716 Скачать руководство пользователя страница 431

GR716-DS-UM, May 2019, Version 1.29

434

www.cobham.com/gaisler

GR716

44

SPI Controller

The GR716 microcontroller comprises two separate SPI controller (SPICTRL) units. Each SPI con-
troller unit controls its own external pins and has a unique AMBA address described in chapter 2.11.
Each SPI controller unit control and status registers are located on the APB bus in the address range 
from 0x80390000 to 0x803AFFFF. See SPICTRL units connections in the next drawing. The figure 
shows memory locations and functions used for SPICTRL configuration and control.

The primary clock gating unit 

GRCLKGATE

 described in section 26 is used to enable/disable SPI 

controller units. The unit 

GRCLKGATE

 can also be used to perform reset of individual SPI control-

ler units. Software must enable clock and release reset described in section 26 before SPI configura-
tion and transmission can start.
External IO selection per SPI controller unit is made in the system IO and LVDS configuration regis-
ter (

GRGPREG

) in the address range from 0x8000D000 to 0x8000D03F and 0x80007030. See sec-

tion 7.1 for further information.
Each 

SPICTRLx

 unit controls its own external pins and has a unique AMBA address described in 

chapter 2.11. SPICTRL unit 0 and 1 has identical configuration and status registers. Configuration and 
status registers are described in this section 44.3
System  can  be  configured to  protect  and  restrict  access  to  individual  SPICTRL  unit  in  the 

MEM-

PROT

 unit. See section 47 for more information.

44.1

Overview

The core provides a link between the AMBA APB bus and the Serial Peripheral Interface (SPI) bus 
and can be dynamically configured to function either as a SPI master or a slave. The SPI bus parame-
ters  are  highly  configurable  via  registers.  Core  features  also  include  configurable  word  length,  bit 

Figure 72.  

GR716 SPICTRLx bus and pin 

GPIO0

LEON3FT

Processor

APB 
(0x80000000-
 0x800FFFFF)

SPICTRL1

  IOMUX

GPIO63

Main AHB 
(0x00000000-
 0xFFFFFFFF)

Select Outputs

Enable SPICTRLx clocks

(0x8000D000 -
 0x8000D03F)

(0x80006000 -
 0x8000600F)

GRGPREG

Select LVDS
(0x80007030)

LVDSMUX

MEMPROT

Memory Protection
(0x8001A000 -
 0x8001AFFF)

Bridge

TX0

RX2

Bridge

GRCLKGATE

Bridge

SPICTRL0

Содержание GR716




































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов