manualshive.com logo in svg

Cisco 7600 Series, Руководство по настройке

Инструкция по эксплуатации Campden instruments 7600 Series доступна для скачивания бесплатно на нашем сайте. Скачайте руководство, чтобы узнать как использовать этот продукт. manualshive.com - ваш источник надежной информации о продукте.

Поделиться
Скачать
background image

36-3

Cisco 7600 Series Router Cisco IOS Software Configuration Guide, Release 12.2SX

OL-4266-08

Chapter 36      Configuring Denial of Service Protection

Understanding How DoS Protection Works

Router(config)# 

access-list 199 deny ip host 192.168.0.0 any

Router(config)# 

access-list 199 permit ip any any 

        

Router(config)# 

interface g9/1

Router(config-if)# 

ip access 199 in                   <======== Note: security ACL applied

Router(config-if)# 

end

Router#

1w6d: %SYS-5-CONFIG_I: Configured from console by console

Router# 

clear mls ip mod 9

Router# 

show mls ip mod 9

   

Displaying Netflow entries in module 9

DstIP           SrcIP           Prot:SrcPort:DstPort  Src i/f:AdjPtr

--------------------------------------------------------------------

Pkts         Bytes       Age   LastSeen  Attributes

---------------------------------------------------

192.168.0.0  192.168.1.0 0   :0      :0        0   : 0         

1542         70932       2     02:31:56   L3 - Dynamic

192.168.1.0  192.168.0.0       0   :0      :0        0   : 0         

0            0           2     02:31:56   L3 - Dynamic  

<======== Note: hardware-forwarded

                                                        <======== Note: traffic stopped

Extended IP access list 199

    deny ip host 192.168.0.0 any (100 matches)

    permit ip any any

Router# 

show access-list 199

Extended IP access list 199

        

deny ip host 192.168.0.0 any (103 matches 

    permit ip any any

Router #

Security VACLs

Security virtual access lists (VACLs) are security-enforcement tools based on Layer 2, Layer 3, and 
Layer 4 information. The result of a security VACL lookup against a packet can be a permit, a deny, a 
permit and capture, or a redirect. When you associate a security VACL with a particular VLAN, all traffic 
must be permitted by the security VACL before the traffic is allowed into the VLAN. Security VACLs 
are enforced in hardware, so there is no performance penalty for applying security VACLs to a VLAN 
on the Cisco 7600 series routers. 

QoS ACLs

Unlike security ACLs, QoS ACLs can be used to limit the rate of traffic without denying access to all 
the traffic in a flow. 

This example shows how to use a QoS ACL to prevent a ping attack on a router. A QoS ACL is configured 
and applied on all interfaces to limit the rate of incoming ICMP echo packets.

Router# 

show ip ospf neighbors

Neighbor ID     Pri   State           Dead Time   Address         Interface

6.6.6.122         1   FULL/BDR        00:00:30    6.6.6.122       Vlan46

Router# 

show ip eigrp neighbors

IP-EIGRP neighbors for process 200

H   Address                 Interface   Hold Uptime   SRTT   RTO  Q  Seq Type

                                        (sec)         (ms)       Cnt Num

0   4.4.4.122               Vl44          11 00:06:07    4   200  0  6555   

Router#                                                 

<======== Note: ping attack starts

Router# 

show proc cpu | include CPU utilization

CPU utilization for five seconds: 99%/90%; one minute: 48%; five minutes: 25%

Router#

2w0d: %OSPF-5-ADJCHG: Process 100, Nbr 6.6.6.122 on Vlan46 from FULL to DOWN, Neighbor 

Down: Dead timer expired

Содержание 7600 Series




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7600 Series

Compaq Proliant 800 Setup And Installation Manual preview
Proliant 800
Бренд: Compaq Страницы: 112
MikroTik RouterBOARD SXT 5HnD Quick Setup Manual And Warranty Information preview
RouterBOARD SXT 5HnD
Бренд: MikroTik Страницы: 2
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Бренд: Enginko Страницы: 19
Fostex DE-1 Service Manual preview
DE-1
Бренд: Fostex Страницы: 20
SurfControl 509-8629-00 Setup Manual preview
509-8629-00
Бренд: SurfControl Страницы: 2
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Бренд: Pressalit Care Страницы: 31
B&B Electronics EIP308 Product Information preview
EIP308
Бренд: B&B Electronics Страницы: 2
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Бренд: Element14 Страницы: 2
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Бренд: Matrix Switch Corporation Страницы: 60
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Бренд: ADTRAN Страницы: 20
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Бренд: Icy Box Страницы: 2
LevelOne WAB-3000 How To Set Up preview
WAB-3000
Бренд: LevelOne Страницы: 11
Alcatel-Lucent 7705 SAR-A Installation Manual preview
7705 SAR-A
Бренд: Alcatel-Lucent Страницы: 154
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Бренд: Genexis Страницы: 7
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Бренд: YASKAWA Страницы: 87
BOSER Technology HS-4703 Manual preview
HS-4703
Бренд: BOSER Technology Страницы: 78
Roland Symphonique Strings SRX-04 Owner'S Manual preview
Symphonique Strings SRX-04
Бренд: Roland Страницы: 12
Silex technology Embedded Intelligent Module SX-560 Developer'S Reference Manual preview
Embedded Intelligent Module SX-560
Бренд: Silex technology Страницы: 110

Бренды по названию

Популярные бренды

Загрузить еще бренды