manualshive.com logo in svg

Cisco 7600 Series, Руководство по настройке

Инструкция по эксплуатации Campden instruments 7600 Series доступна для скачивания бесплатно на нашем сайте. Скачайте руководство, чтобы узнать как использовать этот продукт. manualshive.com - ваш источник надежной информации о продукте.

Поделиться
Скачать
background image

C H A P T E R

32-1

Cisco 7600 Series Router Cisco IOS Software Configuration Guide, Release 12.2SX

OL-4266-08

32

Configuring RGMP

This chapter supplements the information and procedures about Router-Port Group Management 
Protocol (RGMP) in the Release 12.2 publication at this URL:

http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfrgmp.html

 

This chapter consists of these sections:

  •

Understanding How RGMP Works, page 32-1

  •

Default RGMP Configuration, page 32-2

  •

RGMP Configuration Guidelines and Restrictions, page 32-2

  •

Enabling RGMP on Layer 3 Interfaces, page 32-3

Tip

For additional information (including configuration examples and troubleshooting information), see the 
documents listed on this page:

http://www.cisco.com/en/US/products/hw/routers/ps368/tsd_products_support_series_home.html

 

Understanding How RGMP Works

RGMP constrains multicast traffic that exits the Cisco 7600 series router through ports to which only 
disinterested multicast routers are connected. RGMP reduces network congestion by forwarding 
multicast traffic to only those routers that are configured to receive it.

Note

•

To use RGMP, you must enable IGMP snooping on the Cisco 7600 series router. IGMP snooping 
constrains multicast traffic that exits through LAN ports to which hosts are connected. IGMP 
snooping does not constrain traffic that exits through LAN ports to which one or more multicast 
routers are connected.

  •

You must enable Protocol Independent Multicast (PIM) on all routers and switches for RGMP to 
work. Only PIM sparse mode is currently supported.

All routers on the network must be RGMP-capable. RGMP-capable routers send RGMP hello messages 
periodically. The RGMP hello message tells the Cisco 7600 series router not to send multicast data to 
the router unless an RGMP join message has also been sent to the Cisco 7600 series router from that 
router. When an RGMP join message is sent, the router is able to receive multicast data.

Содержание 7600 Series




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7600 Series

ABB i-bus KNX IPR/S 3.5.1 Product Manual preview
i-bus KNX IPR/S 3.5.1
Бренд: ABB Страницы: 44
Conceptronic C150BRS4 Multi Language Quick Manual preview
C150BRS4
Бренд: Conceptronic Страницы: 2
Idis DR-8432 Installation Manual preview
DR-8432
Бренд: Idis Страницы: 31
Patton electronics SMARTNODE 4552 Getting Started Manual preview
SMARTNODE 4552
Бренд: Patton electronics Страницы: 65
Intellinet 523318 Instructions preview
523318
Бренд: Intellinet Страницы: 2
LevelOne FPC-0103T Manual preview
FPC-0103T
Бренд: LevelOne Страницы: 31
Patton electronics SmartNode 4520 Series Getting Started Manual preview
SmartNode 4520 Series
Бренд: Patton electronics Страницы: 90
B&B Electronics EIR208 Series Quick Start Manual preview
EIR208 Series
Бренд: B&B Electronics Страницы: 2
Teletronics International TT 900 User Manual preview
TT 900
Бренд: Teletronics International Страницы: 57
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Бренд: iesy Страницы: 9
Alcatel 7270 MSC Specifications preview
7270 MSC
Бренд: Alcatel Страницы: 4
Serial Cables PCI4-AD-x16HI-BG4 User Manual preview
PCI4-AD-x16HI-BG4
Бренд: Serial Cables Страницы: 15
Belkin F9K1002V1 User Manual preview
F9K1002V1
Бренд: Belkin Страницы: 42
ZyXEL Communications GS1900 Series User Manual preview
GS1900 Series
Бренд: ZyXEL Communications Страницы: 263
NetApp StorageGRID Webscale SG5700 Series Install preview
StorageGRID Webscale SG5700 Series
Бренд: NetApp Страницы: 15
Epson S5U1C6F632T1 Hardware Manual preview
S5U1C6F632T1
Бренд: Epson Страницы: 48
Epson S5U1C63000H6 Manual preview
S5U1C63000H6
Бренд: Epson Страницы: 27
Epson S5U1C63007P Manual preview
S5U1C63007P
Бренд: Epson Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды