manualshive.com logo in svg

Cisco 7600 Series, Руководство по настройке

Инструкция по эксплуатации Campden instruments 7600 Series доступна для скачивания бесплатно на нашем сайте. Скачайте руководство, чтобы узнать как использовать этот продукт. manualshive.com - ваш источник надежной информации о продукте.

Поделиться
Скачать
background image

14-2

Cisco 7600 Series Router Cisco IOS Software Configuration Guide, Release 12.2SX

OL-4266-08

Chapter 14      Configuring VLANs

Understanding How VLANs Work

VLAN Overview

A VLAN is a group of end stations with a common set of requirements, independent of physical location. 
VLANs have the same attributes as a physical LAN but allow you to group end stations even if they are 
not located physically on the same LAN segment.

VLANs are usually associated with IP subnetworks. For example, all the end stations in a particular IP 
subnet belong to the same VLAN. Traffic between VLANs must be routed. LAN port VLAN 
membership is assigned manually on an port-by-port basis. 

VLAN Ranges

Note

You must enable the extended system ID to use 4096 VLANs (see the 

“Understanding the Bridge ID” 

section on page 20-2

).

Cisco 7600 series routers support 4096 VLANs in accordance with the IEEE 802.1Q standard. These 
VLANs are organized into several ranges; you use each range slightly differently. Some of these VLANs 
are propagated to other switches in the network when you use the VLAN Trunking Protocol (VTP). The 
extended-range VLANs are not propagated, so you must configure extended-range VLANs manually on 
each network device. 

Table 14-1

 describes the VLAN ranges. 

The following information applies to VLAN ranges:

  •

Layer 3 LAN ports, WAN interfaces and subinterfaces, and some software features use internal 
VLANs in the extended range. You cannot use an extended range VLAN that has been allocated for 
internal use. 

  •

To display the VLANs used internally, enter the 

show vlan internal usage

 command. With earlier 

releases, enter the 

show vlan internal usage

 and 

show cwan vlans 

commands.

  •

You can configure ascending internal VLAN allocation (from 1006 and up) or descending internal 
VLAN allocation (from 4094 and down). 

  •

You must enable the extended system ID to use extended range VLANs (see the 

“Understanding the 

Bridge ID” section on page 20-2

).

Table 14-1 VLAN Ranges

VLANs

Range

Usage

Propagated

 

by VTP 

0, 4095

Reserved  For system use only. You cannot see or use these VLANs.

—

1

Normal 

Cisco default. You can use this VLAN but you cannot delete it. Yes

2–1001

Normal 

For Ethernet VLANs; you can create, use, and delete these 
VLANs.

Yes

1002–1005 Normal 

Cisco defaults for FDDI and Token Ring. You cannot delete 
VLANs 1002–1005.

Yes

1006–4094 Extended  For Ethernet VLANs only. 

No

Содержание 7600 Series




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7600 Series

B+B SmartWorx CR10 v2 Start Manual preview
CR10 v2
Бренд: B+B SmartWorx Страницы: 4
Hama 39707 Operating Instruction preview
39707
Бренд: Hama Страницы: 4
DCE ANS-205 User Manual preview
ANS-205
Бренд: DCE Страницы: 5
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Бренд: Accusys Страницы: 34
Maxim DS5001FP Specification Sheet preview
DS5001FP
Бренд: Maxim Страницы: 26
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Бренд: NetComm Страницы: 3
BSS Audio EC-4B Installation Manual preview
EC-4B
Бренд: BSS Audio Страницы: 20
Reeven NAIA Installation Manual preview
NAIA
Бренд: Reeven Страницы: 2
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Бренд: Baldor Страницы: 34
Omega OMB-DAQBOARD-3000 Series User Manual preview
OMB-DAQBOARD-3000 Series
Бренд: Omega Страницы: 108
Altera DE2-70 User Manual preview
DE2-70
Бренд: Altera Страницы: 93
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Бренд: ADTRAN Страницы: 46
iBall Baton 150m Configuration Manual preview
150m
Бренд: iBall Baton Страницы: 9
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Бренд: RuggedCom Страницы: 42
Watchguard XTM 850 Hardware Manual preview
XTM 850
Бренд: Watchguard Страницы: 30
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Бренд: Dantel Страницы: 62
Variscite VAR-EXT-CB105 Datasheet preview
VAR-EXT-CB105
Бренд: Variscite Страницы: 18
UfiSpace S9700-23D Hardware Installation Manual preview
S9700-23D
Бренд: UfiSpace Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды