Cisco 3521 Скачать руководство пользователя страница 31

Страница: 31 / 137

1-15

Administrator’s Guide for Cisco IPVC 3521 BRI Gateway, Cisco IPVC 3526 PRI Gateway, and Cisco IPVC 3540 PRI Gateway

OL-7995-01

Chapter 1 Overview of the Cisco IPVC 3500 Series Gateway

About Cisco IPVC 3500 Series Gateway Features

Line quality

Supports line echo cancellation, H.323 Fast Start and DTMF detection for
voice and video calls.

IP network
connection

I10/100Base-T Ethernet connection (on the front panel). A second connection
is for future use.

Serial control port
(DB-9) connection

RS-232 DTE 9-pin D-type connection on front panel for connection to a PC
terminal or an external modem.

Supported signaling
protocols

5ESS and 4ESS, DMS100, National ISDN, Euro-ISDN,
VN6 Dialing (France), NTT (Japan), Hong Kong Dialing
(Hong Kong), Support for Taiwan PRI system.

DMS100, National
ISDN, 5ESS
Custom/Multipoint
(US, Taiwan)

5ESS PTP (US,
Taiwan)

ETSI (France,
Europe, Taiwan,
Hong Kong)

ETSI PTP (France,
Europe, Taiwan)

VN6 Dialing
(France)

Austel 1 Dialing
(Australia)

KDD, NTT (Japan)

Hong Kong Dialing
(Hong Kong).

PRI interface (PRI
Gateways only)

Configurable E1/T1 PRI network interface.

Support for fractional E1/T1 channel selection.

Configurable as terminal side (TE) or network side (NT)
device.

Configurable Long Haul PRI module (supported in Japan
only).

N/A

Switch information
(PRI Gateways only)

Numbering Plan Identifier (NPI), Type of Number
(TON) and Network Specific Facility (NSF) information
elements are configurable for each PRI port.

N/A

Bonding calls (PRI
Gateways only)

Internal Imux providing calls at 128 Kbps (2B) up to full
PRI of 1472 Kbps (23B) for T1 and up to full PRI of
1920 Kbps (30B) for E1 using bonding mode 1.

Parallel dialing for bonded calls.

Internal Imux
providing calls at
128 Kbps (2B) up
to 512 Kbps (8B)
using bonding
mode 1.

Internal IVR
capacity

30 simultaneous calls.

8 simultaneous
calls.

Table 1-8

Cisco IPVC 3500 Series Gateway Feature Specifics

Feature

Cisco IPVC 3540 PRI
Gateway

Cisco IPVC 3526 PRI
Gateway

Cisco IPVC 3521 BRI

Gateway

Содержание 3521










































































































































Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды

Cisco 3521, Руководство администратора

Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды