Cisco 3521 Скачать руководство пользователя страница 82

Страница: 82 / 137

3-20

Administrator’s Guide for Cisco IPVC 3521 BRI Gateway, Cisco IPVC 3526 PRI Gateway, and Cisco IPVC 3540 PRI Gateway

OL-7995-01

Chapter 3 Configuring the Cisco IPVC 3500 Series Gateway

Configuring Gateway Settings

Abnormal disconnect

abnormalDisconnect

.0.11

A call has disconnected
for a reason other than
normal, busy or no
answer.

Warning

ISDN downspeed

isdnDownspeed

.0.12

ISDN downspeeding to a
lower rate is taking place.

Warning

Corrupt IVR messages on
host

corruptIvrMsgOnHost

.0.13

Corrupt IVR files are
present in the gateway.

Warning

Corrupt WEB data

corruptWebData

.0.15

Corrupt web files are
present in the gateway.

Major

ISDN rollover activated

isdnRolloverActivated

.0.16

The gateway notifies the
PSTN switch that the
gateway cannot accept any
further calls. This
command ensures that a
call is completed even
when call volume is high.

ISDN rollover requires
support by the PSTN
switch application and
presumes the availability
of a pool of stacked
gateways across the
managed network.

You can enable ISDN
Rollover only after you set
the gateway to work with
the T1 interface.

Major

Call to peer rejected -
trying alternate

peerCallRejected

.0.43

A call to a peer has been
rejected and the gateway
is searching for an
alternate peer.

Warning

Call from peer rejected due
to capacity

peerCallRejectedCapacity

.0.44

A call from a peer has
been rejected because the
gateway does not have
enough resources
available.

Warning

Call to peer rejected by all
listed peers

peerCallRejectedByAll

.0.

A call to a peer has been
rejected by all listed peers.

Major

Call to peer failed - peer
list empty

peerCallFailedNoPeers

.0.46

A call to a peer has failed
because the peer list is
empty.

Major

Table 3-6

Cisco IPVC 3500 PRI Gateway SNMP Trap Event Types (continued)

Event Type

Trap Name

Trap

OID

Trap is sent when...

State

Severity

Содержание 3521










































































































































Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды

Cisco 3521, Руководство администратора

Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды