Cisco 3521 Скачать руководство пользователя страница 42

Страница: 42 / 137

2-4

Administrator’s Guide for Cisco IPVC 3521 BRI Gateway, Cisco IPVC 3526 PRI Gateway, and Cisco IPVC 3540 PRI Gateway

OL-7995-01

Chapter 2 Installing the Cisco IPVC 3500 Series Gateway

Installing the Cisco IPVC 3521 BRI Gateway in a Rack

•

Cisco Information Packet

Verifying Package Contents for the Cisco IPVC 3540 PRI Gateway

Your Cisco IPVC 3540 PRI Gateway module package contains the following:

•

Cisco IPVC 3540 PRI Gateway module

•

Cisco IPVC 3540 Rear Transition Module for the PRI gateway

•

Terminal cable

•

Regulatory Compliance and Safety Information for Cisco IPVC 3540 Product Family

•

Cisco IPVC Software CD-ROM

•

Cisco Information Package

Installing the Cisco IPVC 3521 BRI Gateway in a Rack

You can install the Cisco IPVC 3521 BRI Gateway in a 19-inch rack. The mounting kit supplied with
the gateway includes two brackets for mounting the unit on a rack.

This section describes how to install

the mounting brackets.

Procedure

Step 1

Place the unit the right way up on a hard flat surface, with the front panel facing you.

Step 2

Position a mounting bracket over the mounting holes on one side of the unit (see

Figure 2-1

Figure 2-1

Mounting Bracket Installation

Step 3

Pass the three screws through the washers and bracket holes into the gateway, and tighten them securely
with a screwdriver.

Step 4

Repeat Steps 2 and 3 for the other side of the gateway.

Step 5

Insert the unit into the 19-inch rack and secure.

Two screws are needed for each side. These screws are not provided.

Note

Make sure that the air vents in the sides of the unit are not blocked.

79472

Содержание 3521










































































































































Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды

Cisco 3521, Руководство администратора

Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды