Cisco 3521 Скачать руководство пользователя страница 85

Страница: 85 / 137

3-23

Administrator’s Guide for Cisco IPVC 3521 BRI Gateway, Cisco IPVC 3526 PRI Gateway, and Cisco IPVC 3540 PRI Gateway

OL-7995-01

Chapter 3 Configuring the Cisco IPVC 3500 Series Gateway

Configuring Gateway Settings

The following channels support encryption:

•

Audio channel

•

Video Channel

•

Far End Camera Control (FECC)

Note

All channels (audio, video, and FECC, incoming, outgoing) on the same call must have the same
encryption levels. If the same encryption on all channels is not achieved, the call disconnects.

In the Security section of the Settings tab, you can configure gateway encryption settings.

Procedure

Step 1

In the Gateway interface, on the sidebar, click

Gateway

(if not already selected).

Step 2

Click the

Settings

tab.

Step 3

Click the

Security

button

Step 4

Select the

Support encryption

check box to enable gateway support for H.235 encryption for H.323

calls.

Step 5

In the

Encryption mode

field, choose one of the following settings:

•

Best effort

•

Encryption required

•

Strong encryption required

Configuring Advanced Settings

In the Advanced section of the Settings tab, you can configure, enable, and disable various advanced
gateway settings.

Table 3-7

Gateway Supported Encryption Capabilities

Mode

Capabilities

Encryption off

Priority 1: No encryption

Best effort

Priority 1: AES 128

Priority 2: DES 56

Priority 3: No encryption

Encryption required

Priority 1: AES 128

Priority 2: DES 56

Strong encryption required

Priority 1: AES 128

Содержание 3521










































































































































Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды

Cisco 3521, Руководство администратора

Результаты поиска

Содержание 3521

Отзывы:

Похожие инструкции для 3521

Бренды по названию

Популярные бренды