Chino KP 2000 Series Скачать руководство пользователя страница 71

Страница: 71 / 144

- 68 -

9. Operation

9-1. Confirmations before operation

Confirm the following contents before starting the operation.

Item Confirmation

contents

1. Wiring

・

Confirm that the wiring is correct.
Especially confirm very properly the wiring of high voltage parts like power
supply, output and alarm. Confirm that the terminal screw is not loose.

・

Confirm the wiring of not only the controller but also of the entire finished

product.

Especially proper confirmation of periphery of operation terminal (thyristor
regulator, heater, motor etc.) is important.

2. Power supply

・

Confirm that the power supply is in the rating range.

3. Set contents

・

Confirm that the set contents are correct.

When power supply is inserted confirm that the status is RESET status. In

RUN status control operation is started immediately. As per the requirement
if output is not to be displayed, set 0% in manual output operation.

Precautions

①

If power supply other than the rated power supply is connected, this

controller may become out of order, or its performance may
deteriorate or it may malfunction etc.

②

If excessive current or excessive voltage is applied to input output

terminal of this controller, this controller may become out of order, or
its performance may deteriorate or it may malfunction etc.

9-2. Program operation and run operation

9-2-1. Run operation

Status

Key operation and operation

screen

Description

1. RESET

[Key operation]
In operation screen, click
the



key and then click



key.

[Operation screen]

・

Resets (release) the program operation.

・

It is enabled in RUN status or STOP status.

・

RESET status is the status in which program operation

is not executing, output value is 0% and alarm operation
does not run.

・

When the step number is progressing due to program

operation etc., the step number returns to '00' due to
RESET operation.

・

In case of constant value operation in RESET status,

as it is a normal control operation, alarm operation is
also executed.

Содержание KP 2000 Series

















































































































































Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды

Chino KP 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды