Chino KP 2000 Series Скачать руководство пользователя страница 67

Страница: 67 / 144

- 64 -

7-15. Error message

7-15-1. Usual error display

If proper settings and operation is not done, following error messages are displayed for around 3 seconds.

Confirm the contents of the error message and do the proper settings and operation again.

Error message

Error contents

・

SV is exceeding the measurement range.

・

Confirm the measurement range and do the settings again.

・

Pattern cannot be eliminated during operation (RUN).

・

Eliminate the pattern when it is not operating.

・

Pattern of the copying destination is not cleared.

・

Confirm the copying destination and do the settings again.

・

Pattern of copy source is not set.

・

Set the pattern of copy source.

・

Pattern is not set.

・

Set the pattern.

・

AT1 is not starting as screen is not operating (RUN).

・

Start AT1 after operating (RUN) the screen.

・

AT2 is not starting as status is not RESET status.

・

Start AT2 after changing the status to RESET.

・

AT3 is not starting as status is not RESET status.

・

Start AT3 after changing the status to RESET.

・

AT4 is not starting as status is not operating (RUN).

・

Start AT4 after changing to operate (RUN).

Содержание KP 2000 Series

















































































































































Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды

Chino KP 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды