Chino KP 2000 Series Скачать руководство пользователя страница 46

Страница: 46 / 144

- 43 -

7-6. Mode 4

Mode 4 performs the setting related to output.

Settings screen

Description of the screen

1. Mode screen

[Lock Status]

[Display OFF status]

①

Mode 4 screen.

②

By clicking the



･



key, 'Lock' and 'NoDisp' is displayed.

③

For mode 4 settings screen, if setting change is to be prohibited

select 'Lock'.

④

When doing the settings by communications, set all the mode

screens to 'Lock'.

⑤

When settings screen of mode 4 is not displayed, select 'NoDisp'.

2. Output limiter 8 types

[Output scaling specifications]

Option

Output limiter

①

Set 8 types of output limiters.

②

Set lower limit of output limiter in 'L' , and upper limit of output limiter
in 'H'.

③

In either of automatic output operation and manual output operation
the output is within this setting range.

④

After the settings, it is necessary to set the output limiter number
that is to be used for each pattern/step in mode 2.

Output scaling (Option)

①

Set 8 types of output scaling.

②

Set lower limit of output scaling in ‘L’, and upper ;limit of output

scaling in ‘H’.

③

In case of automatic output operation, output is scaled within rage

of this setting, however in case of manual output operation, output
is not scaled.

④

After the setting, set the which output scaling No. is used in each

pattern /step at mode 2.

3. Second output limiter

[Output scaling specifications]

Option

Second output limiter

①

It is displayed in case of output 2 specifications only.

②

Set the output limiter of output 2 side.

③

Set lower limit of output limiter in 'L' , and upper limit of output limiter
in 'H'.

④

In either of automatic output operation and manual output operation
the output is within this setting range.

Second output scaling (Option)

①

It is displayed in case of output 2 specifications only.

②

Set the output scaling of output 2 side.

③

Set lower limit of output scaling in ‘L’, and upper ;limit of output

scaling in ‘H’.

④

In case of automatic output operation, output is scaled within rage

of this setting, however in case of manual output operation, output
is not scaled.

Содержание KP 2000 Series

















































































































































Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды

Chino KP 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды