Chino KP 2000 Series Скачать руководство пользователя страница 54

Страница: 54 / 144

- 51 -

7-9. Mode 7

Mode 7 performs the setting related to transmission signal output.

Settings screen

Description of the screen

1. Mode screen

[Lock status]

[Display OFF status]

①

Mode 7 screen. Only the specifications with transmission signal

output are displayed.

②

By clicking the



･



key, 'Lock' and 'NoDisp' is displayed.

③

For mode 7 settings screen, if setting change is to be prohibited

select 'Lock'.

④

When doing the settings by communication, set all the mode

screens to 'Lock'.

⑤

When settings screen of mode 7 is not displayed, select 'NoDisp'.

2. Transmission types

(High-performance type)

①

Displays only the specifications with transmission signal output

(High performance type).

②

Sets transmission type of high-performance type.

③

When 'PV' is selected, measurement value (PV) is transmitted.

④

When 'SV' is selected, setting value (SV) is transmitted.

⑤

When 'MV' is selected, output value (MV) is selected.

⑥

When 'MFB' is selected, operation terminal feedback value (MFB) is

transmitted, but ON-OFF servo type only.

⑦

If 'SUB' is selected, setting value of subsidiary output is transmitted.

Settings of subsidiary output become '8 types subsidiary output ' of
mode 7.

⑧

In case of output 2 specifications, output 1 side 'MV1' and output 2

side 'MV2' can be selected separately.

⑨

When transmission type is changed sometimes setting range and

decimal point position changes or it may be initialized automatically
and relatively hence take care.

3. Transmission scale

(High-performance type)

①

Specifications with transmission signal output (High-performance

type) only are displayed.

②

Set a scale corresponding to transmission signal output (analog

signal) of high performance type.

③

Set lower limit (0%) and higher limit (100%) of the scale for the

minimum value (0%) and maximum value (100%) of the
transmission signal output.

④

When transmission scale is changed, sometimes setting range and

decimal point position changes automatically and relatively hence
take care.

Содержание KP 2000 Series

















































































































































Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды

Chino KP 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды