Chino KP 2000 Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 144

background image

- 78 -

10-3. Alarm mode

Following are the types of alarm formats.

①

PV (Measurement value alarm)

･

PV (Absolute value alarm)

: PV alarm due to alarm setting value.

･

DV (Deviation alarm)

: SV+PV alarm depending to alarm setting value.

･

ADV (Absolute value deviation alarm) : SV±PV alarm due to alarm setting value.

Ú

Set integer number (absolute value) for alarm value.

②

SV (Setting value alarm)

･

SV (Setting value alarm)

: SV alarm due to alarm setting value.

③

MV (Output value) alarm

･

MV (Output value alarm)

: MV alarm due to alarm setting value.

Ú

In case of output 2 specifications, it becomes the output value

(MV1) alarm of output 1.

④

Control related alarms

･

CT (Heater snapping wire alarm)

: CT measurement value alarm due to alarm setting value.

Ú

Only specifications with heater snapping wire alarm can be

selected.

⑤

FAIL (Abnormal alarm)

･

FAIL (Fail alarm)

: RJ data abnormal, A/D conversion abnormal.

Ú

Setting value does not exist.

⑥

Timer

･

TIMER

: Timer combined with external signal input.

Ú

Only specifications with external signal input can be selected.

⑦

Wait time alarm

･

WAIT (Wait alarm)

: Real temperature compensation.

In addition select the following conditions in alarm format

①

to

③

, mentioned above.

･

H (High limit alarm)

: Alarm turns ON if alarm setting value is exceeded.

･

L (Low limit alarm)

: Alarm turns ON if alarm setting value is less.

･

HW (Wait high limit alarm)

: In a system that has wait function in high limit alarm, keep the

alarm ON in wait status until it once enters the normal range.
When RUN is performed from RESET status or ADV (stepping) is
performed, it becomes wait status.

･

LW (Wait low limit alarm)

: In a system that has wait function in low limit alarm, keep the

alarm ON in wait status until it once enters the normal range.
When RUN is performed from RESET status or ADV (stepping) is
performed, it becomes wait status.

･

HK (Maintenance high limit alarm)

: In a system that has maintenance function in high limit

alarm, the alarm ON status is maintained from the time when
alarm is switched ON to the time when it is cancelled.

Ú

Alarm is cancelled by alarm output cancellation, switching to

RESET from program operation, or OFF/ON of power.

･

LK (Maintenance low limit alarm)

: In a system that has maintenance function in low limit

alarm, the alarm ON status is maintained from the time when
alarm is switched ON to the time when it is cancelled.

Ú

Alarm is cancelled by alarm output cancellation, switching to

RESET from program operation, or OFF/ON of power.

･

HWK (Wait maintenance high limit alarm): It is a system that has wait function and maintenance function in

high limit alarm.

･

LWK (Wait maintenance low limit alarm) : It is a system that has wait function and maintenance function in

low limit alarm.

*Alarm calculation is performed in program operation and constant value operation, not in RESET.

«
...
79
80
81
82
83
...
»

Содержание KP 2000 Series

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для KP 2000 Series

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: XBOX Страницы: 2

Бренд: jbc Страницы: 4

Бренд: YASKAWA Страницы: 256

Бренд: Calsense Страницы: 74

Бренд: Harsco Industrial Страницы: 57

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

FieldPoint FP-1001

Бренд: National Instruments Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды