Chino KP 2000 Series Скачать руководство пользователя страница 5

Страница: 5 / 144

- 2 -

■

Before use

After opening the pack, confirm the following before using the product. Although it is rare but if you notice

anything wrong, contact your dealer or our nearest office.

1. Confirm the exterior

Confirm that the product is not broken on the outer side.

1. Confirm the model code

Confirm that the model code is that of the model that you want to purchase.

◆

Model code label and its location

A label as shown below is pasted on the upper surface of the controller unit.

ＫＰ２□□□□□□□－□□□

←

Model code

□□□□□□□□□

←

Serial number

MADE IN JAPAN

3. Confirm the accessories

The following accessories are attached to the controller, confirm them.

Name Quantity

Remarks

Mounting bracket

2 (1 set)

For panel mounting

Contact protection element

Attached to ON-OFF servo type specifications

only

Instruction manual (General)

This document

Instruction manual

(Communications interface)

Attached to communications specifications only

(in CD-R)

When accessories are requested separately, sometimes those are also attached.

1. Do not drop the instrument while taking it out of the box.
2. When transporting this instrument, pack the instrument in the box and then put it with cushions in another

box. We recommend keeping the box for transport.

3. When not using the instrument for a while after taking it from the panel, put the instrument in the box and

store at room temperature and in a dust free atmosphere.

Attention

Содержание KP 2000 Series

















































































































































Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды

Chino KP 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание KP 2000 Series

Отзывы:

Похожие инструкции для KP 2000 Series

Бренды по названию

Популярные бренды