Chino KP 2000 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 144

background image

- 23 -

6. Operation screen

Lower display window displays operation screen and settings screen. The operation screen has an output

display screen whose display contents differ depending on the output format of the product, the time display
screen that displays progress time of program pattern, and a overall display screen.

6-1.Output display screen

Output display screen

Description of screen

[ON-OFF pulse type]

[SSR drive pulse type]

Ú

The above is a mock display.

Actually

and

do not

light simultaneously.

①

On the left bottom, a snap display of three steps, the

executing step in the middle and its previous and the next
step are displayed. In case of RUN status, the executing step
in the middle blinks.

②

illuminates when output status is ON and

illuminates when output status is OFF.

③

Displays MV (output value) digitally.

④

At the time of manual output operation (manual output) 'M' on
the left of 'OUT' illuminates.

⑤

In case of specifications with heater snapping wire alarm, CT

measurement value is digitally displayed by 'Existence of CT
screen' of mode 1.However if it cannot be measured it
displays '----'.

[Current output type]

[Voltage output type]

①

On the left bottom, a snap display of three steps, the

executing step in the middle and its previous and the next
step are displayed. In case of RUN status, the executing step
in the middle blinks.

②

Displays a bar graph corresponding to the output value.

③

Displays MV (output value) digitally.

④

At the time of manual output operation (manual output) 'M' on

the left of 'OUT' gets illuminated.

[ON-OFF servo type]

Ú

The above is a mock display.

Actually

and

do not illuminate

simultaneously.

①

On the left bottom, a snap display of three steps, the
executing step in the middle and its previous and the next
step are displayed. In case of RUN status, the executing step
in the middle blinks.

②

When signal on the close side is ON

illuminates

and when signal on the open side is ON

illuminates.
When both the signals are OFF nothing is illuminated.

③

Displays MV (output value) digitally.

④

Displays feedback value (extent of valve opening) digitally.

⑤

At the time of manual output operation (manual output) 'M' on

the left of 'OUT' is illuminated.

«
...
24
25
26
27
28
...
»

Содержание KP 2000 Series

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для KP 2000 Series

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Watts Страницы: 8

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: DSEGenset Страницы: 74

Бренд: ITALFARAD Страницы: 32

Бренд: Comet Страницы: 9

Бренд: Roger Страницы: 21

Бренд: BEBE CONFORT Страницы: 90

Бренд: Daikin Страницы: 40

Бренд: Carel Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды