Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 49

Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 43

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

42

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

OPTIONAL FEATURES

cont.

AIR BLAST

The Model 93 offers the capability to add a

#93AB

Air Blast feature. The components necessary to add this feature must

be purchased separately and can be installed by the user.
This feature is used to clear away insulation slugs when performing a full strip on the leading end of the wire. This feature
may not always be necessary to use.

INSTALLATION

1.  Turn machine off and unplug.
2.  Remove the 6 screws that secure the back cover on the cabinet.
3.  Inside the machine, locate the clear air line that is secured to the corner of the right hand fan. Cut the wire tie

securing the air line to the fan. Connect this line to Port #2 on

#8840

Air Blast Solenoid Valve.

#7385 Air Line-8”

#8841 Air Blast
Solenoid Valve Wire Harness

#7360 Air Fitting 2 ea.

#7385 Air Line-4’
#3413 Air Fitting Attached

#3876 Screw 2 ea.

#8840 Air Blast Solenoid

#3413 Air Fitting

#7360 Air Fitting attached to
#3868 Bushing

«
...
41
42
43
44
45
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов