Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 49

background image

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

21

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

SHORT MODE

cont.

LENGTH CORRECTION

  The Model 93 has a Length Correct feature that allows the operator to make adjustments from the preprogrammed length
  versus the actual sample length. This feature allows for correction for both overall cut length and strip length. Small
  variations from the programmed value to the actual value are normal due to differences in material, tension, friction, wire
  diameter etc. If the sample wire did not have the correct length and/or strip length select the

LENGTH CORRECT

key for

adjustments.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER

This screen is used to make corrections to the

overall

length. Measure the length of

MEASURED WIRE LENGTH

your sample piece. If overall length correction is necessary enter the actual measured

value and then Press

ENTER.

The Model 93 will automatically calculate the correction

necessary. Run several test pieces to check correction. NOTE: If the overall length

requires no correction do not enter a value.

PLEASE ENTER

This screen is used to make corrections to the

strip

length. If strip length corrections

SHORT

MODE

are necessary proceed as follows: First, run several test pieces to insure overall length

CORRECTION VALUE

is correct. Then, measure the Leading End of your sample pieces. The CORRECTION

CORRECT= 0.00

VALUE will be the difference between the programmed dimension and the actual

measured dimension. Enter this value and then Press

ENTER

. Run several test pieces

to check correction. NOTE:If the strip length requires no correction do not enter a

value.

  The possible range of correction is +/- 10% of the overall wire length. If a value outside of this range is entered an error
  message will appear and display the acceptable range of values.
  The length correct value may be changed multiple times but typically a single entry is all that is required if the sample wire
  was measured accurately and the data entered correctly.

RUN PROGRAM

After you have produced a satisfactory sample wire and all settings are correct press

RUN.

This will process your current

program. The same warning will appear as noted above in SINGLE CYCLE. Make sure that the Exit Guide and Trailing
Strip Rollers are removed.

STOP PROGRAM

If at any time you need to stop your processing press

STOP.

This action will stop the processing and wire feed.

LENGTH

CORRECT

RUN

STOP

«
...
20
21
22
23
24
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов

Похожие инструкции для Compu-Strip 93

Camm-1 PNC-1200

Бренд: Roland Страницы: 53

Бренд: D-CUT Страницы: 7

Бренд: Zenoah Страницы: 24

Бренд: Jonsered Страницы: 32

Бренд: Jonco Страницы: 15

Бренд: Jonsered Страницы: 44

Бренд: AL-KO Страницы: 244

Бренд: Lincoln Electric Страницы: 42

Compact Elite 350-1

Бренд: Logan Страницы: 9

Бренд: WilTec Страницы: 28

Diamond3 FB750W

Бренд: B+BTec Страницы: 36

Бренд: Hiace Страницы: 12

Бренд: Racing Страницы: 26

Бренд: Value Leader Страницы: 34

GRA-TECH WIS000001-2

Бренд: Kasanova Страницы: 16

Бренд: Oleo-Mac Страницы: 76

Бренд: RASOR Страницы: 15

Бренд: Malco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды