Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 21

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

20

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

AMOUNT TO PROCESS
PER

BATCH

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

SHORT MODE

cont.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE

SELECT

Use the arrow keys to select

BATCH

or

TOTAL

display mode. Press

ENTER.

AMOUNT TO DISPLAY

BATCH

mode will count DOWN the number of pieces per batch.

TOTAL

mode will

DISPLAY = BATCH

count

UP the number of pieces per batch. Both modes will display on the screen

BATCH TOTAL

the descending or ascending piece count of the current batch being processed. The

display will also show the current batch number being processed/total batches to be

processed.

PRESS CLEAR TO

This screen will display the running total number of pieces that have been processed

RESET TOTAL COUNTER

from the current batch sequence. This amount maybe reset to zero or left alone.

OR PRESS ENTER

Press

ENTER.

TOTAL=

ROLLER PRESSURE

  Roller pressure is adjusted by turning the knobs on the front of the machine labeled LEADING STRIP PRESSURE and
  TRAILING STRIP PRESSURE. The goal is to achieve enough pressure to hold the wire and remove any insulation. Too
  little pressure allows the wire to slip between the rollers.  Slippage may cause incorrect “slug pull” dimension. Too much
  pressure may result in wire not tracking straight through the machine. You may have to adjust the pressure a couple of
  times to achieve the desired grip.

The Model 93 is now programmed to process your wire. You are now ready to run a sample wire and check for initial strip
quality. The following will assist you in processing your sample.

SINGLE CYCLE

LCD DISPLAY PROMPT

ACTION REQUIRED

Press SINGLE CYCLE key. This will produce one complete sample wire to check for

accuracy.

PREPARE UNIT FOR

This warning statement will appear to remind you to remove the Exit Guide and Trailing

SHORT WIRE MODE

Strip Feed Rollers. Press

RUN.

If corrections are necessary for anything but overall

LENGTH CORRECTION

length, then select the corresponding key on the Control Panel and make your

THEN PRESS RUN

adjustments. If length corrections are necessary then proceed to

LENGTH

CORRECTION

.

SINGLE

CYCLE

«
...
19
20
21
22
23
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов