Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя | Manualshive

Страница: 27 / 49

background image

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

26

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

  Roller pressure is adjusted by turning the knobs on the front of the machine labeled LEADING STRIP PRESSURE and
  TRAILING STRIP PRESSURE. The goal is to achieve enough pressure to hold the wire and remove any insulation. Too
  little pressure allows the wire to slip between the Feed Rollers. Slippage may cause incorrect “slug pull” dimension. Too
  much pressure may result in wire not tracking straight through the machine. You may have to adjust the pressure a
  couple of times to achieve the desired grip.

The Model 93 is now programmed to process your wire. You are now ready to run a sample wire and check for initial strip
quality. The following will assist you in processing your sample.

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

WINDOW STRIP MODE

cont.

SINGLE CYCLE

Select

SINGLE CYCLE

key to produce one complete sample wire to check for accuracy. If corrections are necessary for

anything but overall length, then select the corresponding key on the Control Panel and make your adjustments. If length
corrections are necessary then proceed to

LENGTH CORRECTION

.

LENGTH CORRECTION

  The Model 93 has a Length Correct feature that allows the operator to make adjustments from the preprogrammed length
  versus the actual sample length. Small variations are normal due to differences in material, tension, friction, wire diameter
  etc. If the sample wire was not the correct length select the

LENGTH CORRECT

key for adjustments.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER

Measure the length of the sample wire produced; enter this value for length.

MEASURED WIRE LENGTH

Press

ENTER

. The

Model 93 will automatically calculate the correction necessary.

The

0.00

next sample should be the

exact length you programmed.

  The possible range of correction is +/- 10% of the overall wire length. If a value outside of this range is entered an error
  message will appear and display the acceptable range of values.
  The length correct value may be changed multiple times but typically a single entry is all that is required if the sample wire
  was measured accurately and the data entered correctly.

SINGLE

CYCLE

LENGTH

CORRECT

«
...
25
26
27
28
29
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов

Похожие инструкции для Compu-Strip 93

Бренд: Makita Страницы: 372

Бренд: Makita Страницы: 19

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 11

Бренд: Makita Страницы: 24

Бренд: Malco Страницы: 2

Бренд: Hilti Страницы: 196

Бренд: Huawei Страницы: 24

$HP Latex Plus Assembly Instructions Manual preview$

Бренд: HP Страницы: 16

Javelin Integra

Бренд: KEENCUT Страницы: 13

Бренд: McCulloch Страницы: 17

Бренд: Holmatro Страницы: 122

GCU 50 i EVO 3 Series

Бренд: Holmatro Страницы: 161

Бренд: Holmatro Страницы: 180

Бренд: QEP Страницы: 8

Бренд: ST. SpA Страницы: 44

Бренд: X4TOOLS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды