Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя | Manualshive

Страница: 42 / 49

background image

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

41

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]



If the unit is set up to both mark and window strip, the Window Pull Correct feature will be disabled. If it becomes
necessary to adjust the Window Pull Dimension, it will need to be done by increasing or decreasing the Window Pull
value by the appropriate amount.



If the unit is set up for marking and the

LOAD WIRE

or

UNLOAD WIRE

keys are pressed at any time after the marker

setup, all correction values will be lost and must be re-entered before processing can continue.



To turn marker option off, press

MENU

and

WIRE MARKER

will appear on screen. Press arrow key under

OFF

and

Press

ENTER.

Marker option is now turned off.

CARPENTER MODEL 93 COMPU-STRIP

OPTIONAL FEATURES

cont.

WIRE STACKER

The Model 93 offers the capability to add on a Wire Stacker to collect longer wire lengths. The electrical interface
necessary to add this equipment must be purchased separately and installed at the factory.

**IMPORTANT**

Please read their operators manual before proceeding.

MACHINE SETUP



To activate interface between the Model 93 and Wire Stacker, install exterior cable

between both units. Plug receptacle on Model 93 is located on the back of the cabinet.



To access Wire Stacking program setup press the

MENU

key.



After Wire Stacking mode is activated a small square will appear on the lower left side of the LCD display.



All dimensions entered during setup will correspond with the unit of measure that is programmed into the machine.

LCD DISPLAY PROMPT

ACTION REQUIRED

WIRE STACKER ON/OFF

Press

ENTER

to select this option.

WIRE STACKER IS ON/OFF

Press the arrow key under

ON

. Press

ENTER.

OFF ON

PLEASE ENTER

Enter the stacker dwell time. This time is determined by the time it takes the stacker to

STACKER DWELL TIME

complete it’s cycle for the current wire being processed. The dwell time range is from

_ _ _ SECONDS

0 to 2.50 seconds. Enter selected time and press

ENTER.

Wire
Stacker
Plug

Wire
Marker
Plug

«
...
40
41
42
43
44
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов

Похожие инструкции для Compu-Strip 93

Cross Tools CSC 350-2000 PRO

Бренд: T.I.P. Страницы: 28

Бренд: ZIPPER MASCHINEN Страницы: 42

Бренд: Teryair Страницы: 12

Бренд: Far Tools Страницы: 42

Бренд: Metabo Страницы: 55

Бренд: Bush Hog Страницы: 1

Бренд: GMP Страницы: 24

Бренд: RASOR Страницы: 15

Бренд: Gardeo Страницы: 84

Бренд: Lamello Страницы: 36

SmarTrac SC Series

Бренд: Ioline Страницы: 66

SmarTrac 100 Series

Бренд: Ioline Страницы: 66

Бренд: Spellbinders Страницы: 20

Бренд: SIZZIX Страницы: 3

Бренд: Stiga Страницы: 33

Бренд: Partner Страницы: 16

Бренд: Partner Страницы: 28

Бренд: Hiace Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды