Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя

Страница: 40 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

REPRESENTATIVES

Factory use only.

RESERVED

Factory use only.

CARPENTER MODEL 93 COMPU-STRIP

OPTIONAL FEATURES

WIRE MARKER

The Model 93 is capable of interfacing with various manufacturers of Hot Stamp Wire Marking units. The electrical
interface necessary to add this equipment must be purchased separately and installed at the factory.

**IMPORTANT**

Please read their operators manual before proceeding.

MACHINE SETUP



To activate interface between the Model 93 and Wire Marker, install exterior cable

between both units. Plug receptacle on Model 93 is located on the back of the cabinet.



To access Wire Marking program setup press the

MENU

key.



After Wire Marking mode is activated

MRK

will appear on the left side of the LCD display.



All dimensions entered during setup will correspond with the unit of measure that is programmed into the machine.

LCD DISPLAY PROMPT

ACTION REQUIRED

WIRE MARKING

Press

ENTER.

WIRE MARKER IS

Press arrow key under

ON.

Press

ENTER.

OFF ON

PLEASE

ENTER

Refer to Wire Marker manufacturers operators manual for suggested settings.

MARK DWELL TIME

Enter dwell time using numeric keys.

_.__ SECONDS

Press

ENTER.

PLEASE

ENTER

With a tape measure, measure the distance from the center of the marking disc to the

MARKER CENTER TO

center of the blades on the Model 93. Once measurement is made enter that amount

BLADE DISTANCE _.__

using the numeric keys. Press

ENTER.

PLEASE ENTER

This measurement is the distance from the leading end(right end) of the wire to the

LEADING END MARK

center of the mark on the wire. Enter distance amount using numeric keys. Maximum

DISTANCE. _.__

distance is (Wire Length/2). Press

ENTER.

PLEASE

ENTER

This measurement is the distance from the trailing end(left end) of the wire to the

center

TRAILING END MARK

of the mark on the wire. Enter distance amount using numeric keys. Maximum

DISTANCE. _.__

distance is ((Wire Length/2) - .20). Press

ENTER.

PLEASE

ENTER

The Model 93/Wire Marker system allows you to program continuous marking along the

CONTINUOUS

MARKING

wire in addition to the end marking. To choose that option enter the distance between

Wire
Stacker
Plug

Wire
Marker
Plug

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды