Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя | Manualshive

Страница: 14 / 49

background image

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

13

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

NORMAL MODE

cont.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER TRAIL

The trailing strip depth will always default to the same as the leading strip depth. This

BLADE STRIP DEPTH

value may be changed if necessary.

OR PRESS ENTER
STRIP DEPTH =

PLEASE ENTER

This controls the length of time the blades will pause at both the Leading and Trailing

BLADE DWELL TIME

Strip depths. When stripping thick or hard to cut insulation a longer dwell time may

0.00 SECONDS

be necessary to allow the blades to cut through the insulation and provide a clean strip.

Enter a value between 0.01 – 2.50 seconds. Press

ENTER

.

PLEASE ENTER

The step back controls the amount which the blades retract after cutting the wire

STEP BACK DISTANCE

insulation and before pulling the insulation off the wire. Example: After running a test

STEP BACK =

wire through the Model 93 you see that the inner conductor has been scraped. You

would now enter a value (.001”-.050”) to retract the blades. This value is automatically
added to the entered Blade Depth so that a clean strip can be obtained.

IMPORTANT

:

There is a big difference between “nicking” and “scrapping” the inner conductors of the
wire. Nicking is when the blades cut too deep into the insulation, and is observed right
at the shoulder of the stripped wire. Scraping is observed not at the shoulder of the
strip, but along the length of the inner conductor as the insulation slug is stripped from
the wire. Nicking is corrected using the

Blade Strip Depth

feature and scrapping is

corrected using the

Step Back

feature.

Press

ENTER.

PLEASE ENTER BLADE

The Model 93 will default to a blade speed appropriate to the type of wire/cable being

SPEED(1 THRU 4)

processed. You may accept or change this value.

DEFAULT IS 1

Press

ENTER

SPEED

=

PLEASE ENTER

Enter the Guide Tube Size previously determined and installed on machine.

GUIDE TUBE SIZE

Press

ENTER. NOTE:

It is important to enter the correct Guide Tube number because

GUIDE TUBE =

this entry controls the blade opening.

Press

FEED SPEED

key. This setting determines the speed of the wire passing

through the machine.

PLEASE ENTER FEED

Select 1-slow, 2-slow/medium, 3-medium ,4 -fast. Press

ENTER.

SPEED (1 THRU 4)

NOTE:

When selecting speed 1 or 2 the maximum Pull Speed that can be selected is

4.

SPEED =

Press

PULL SPEED

key. This setting determines the pull force of insulation being

removed.

FEED

SPEED

PULL

SPEED

«
...
12
13
14
15
16
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов

Похожие инструкции для Compu-Strip 93

Бренд: Wolfcraft Страницы: 52

Бренд: Greenlee Страницы: 18

Бренд: D-CUT Страницы: 5

Бренд: Shindaiwa Страницы: 40

Бренд: Redmond Страницы: 136

Бренд: HOLZMANN MASCHINEN Страницы: 36

Heat Cutter 90 W

Бренд: LK Страницы: 2

Бренд: Ryobi Страницы: 28

A Class Mark II

Бренд: Datamax Страницы: 14

Бренд: Proxxon Страницы: 16

brushcutter TBC-205

Бренд: Tanaka Страницы: 15

Бренд: Gartenteile Страницы: 96

Бренд: KEENCUT Страницы: 32

Бренд: Cedima Страницы: 42

Бренд: Panasonic Страницы: 22

Бренд: GMC Страницы: 52

Бренд: Makita Страницы: 44

Бренд: Makita Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды