Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя

Страница: 10 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

SETUP

cont.

LOADING WIRE

Open the Leading Strip and Trailing Strip Rollers far enough to allow the wire to pass through freely. Feed the wire
through

the Wire Straightener, underneath the Out of Material Rod, through the Centering Rollers, through the

Leading Strip Rollers

and just into the entrance of the Input Guide Tube. Adjust the Centering Rollers up to the

wire but not touching the wire. Adjust the Leading Strip Rollers until they make contact with the wire. Select

LOAD WIRE

key and keep it pressed down until the wire is completely fed through the machine. Once the wire has exited, release the
switch. The LCD screen will

display

CHECK TRAILING

STRIP ROLLER PRESSURE, THEN CLOSE GUARD AND

PRESS ENTER

. Adjust the

Trailing Strip Rollers until they make contact with the wire, close the Safety Guard and then

Press

ENTER

. This will cut the wire and feed the slug from the machine. The Model 93 is now ready to program and

process your wire.

PLEASE NOTE THE MODEL 93 IS PICTURED WITHOUT THE SAFETY GUARD FOR DEMONSTRATION PURPOSES ONLY.

#5459 Thumb Screw
#8815 Exit Guide

#8500 Input Guide Tube
#8087 Thumb Screw

Centering Rollers Adjustment Knob

Out of Material Rod

Leading Strip Roller
Adjustment Knob

Trailing Strip Roller
Adjustment Knob

LOAD

WIRE

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды