Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 49

Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 35

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

34

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

PROGRAMMING

FLAT CABLE MODE

cont

.

LENGTH CORRECTION

  The Model 93 has a Length Correct feature that allows the operator to make adjustments from the preprogrammed length
  versus the actual sample length. Small variations are normal due to differences in material, tension, friction, wire diameter
  etc. If the sample wire was not the correct length select the

LENGTH CORRECT

key for adjustments.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER

Measure the length of the sample wire produced; enter this value for length.

MEASURED WIRE LENGTH

Press

ENTER

. The

Model 93 will automatically calculate the correction necessary.

The

0.00

next sample should be the

exact length you programmed.

  The possible range of correction is +/- 10% of the overall wire length. If a value outside of this range is entered an error
  message will appear and display the acceptable range of values.
  The length correct value may be changed multiple times but typically a single entry is all that is required if the sample wire
  was measured accurately and the data entered correctly.

RUN PROGRAM

After you have produced a satisfactory sample wire and all settings are correct press

RUN.

This will process your current

program.

STOP PROGRAM

If at any time you need to stop your processing press

STOP.

This action will stop the processing and wire feed.

UNLOADING WIRE

LENGTH

CORRECT

RUN

STOP

UNLOAD

WIRE

«
...
33
34
35
36
37
...
»

Содержание Compu-Strip 93


















































Отзывы:

Нет отзывов