Carpenter MFG. Co., Inc. Compu-Strip 93 Скачать руководство пользователя страница 39

Страница: 39 / 49

CARPENTER MODEL 93 COMPU-STRIP

Phone: 315-682-9176 Fax: 315-682-9160

Page

Revised 08/23/13 Website: www.carpentermfg.com E-mail: [email protected]

CARPENTER MODEL 93 COMPU-STRIP

SPECIAL FEATURES

cont.

PASSWORD ON/OFF

The Model 93 comes equipped with a Password feature. When the password is activated the ability to change program
data is prohibited.

LCD DISPLAY PROMPT

ACTION REQUIRED

PASSWORD IS OFF

Press

ARROW

key to select ON.

OFF ON

Press

ENTER.

PASSWORD IS ON

Enter factory set password “123”.

ENTER PASSWORD

Press

ENTER.

STORE NEW PASSWORD

This option will allow you to change the password at your discretion.

LCD DISPLAY PROMPT

ACTION REQUIRED

PLEASE ENTER

Enter old password.

OLD PASSWORD

Press

ENTER.

PLEASE ENTER

Enter a new password up to 5 digits.

NEW PASSWORD

Press

ENTER.

WIRE SENSOR

The Model 93 comes with a Wire Sensor/Out of Material switch. If the sensor is activated the Model 93 will automatically

shut off when it runs out of material. If the sensor is not activated the machine will continue to run and finish the current
program until programmed amount reaches zero. You may choose to turn this option on or off.

LCD DISPLAY PROMPT

ACTION REQUIRED

WIRE SENSOR IS OFF

Press

ARROW

key to select ON or OFF.

OFF ON

Press

ENTER.

Содержание Compu-Strip 93


















































Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды

Carpenter MFG. Co., Inc. Compu-Strip 93, Руководство оператора

Результаты поиска

Содержание Compu-Strip 93

Отзывы:

Похожие инструкции для Compu-Strip 93

Бренды по названию

Популярные бренды